Rough idling 3Fe

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 15, 2007
Threads
89
Messages
478
Location
30°54'01.53N / 84°04'56.04W
Went wheeling a few days ago, truck started acting up when idling in 4L. Seems to almost die (dash lights come on like its in ACC mode, then the engine surges, then immediately almost dies again, then surges. Was worse in reverse. Getting to the point now that it actuall does die.

Now its getting to the point of getting worse even sitting at a stop light. Almost dies, then surges...

Seems to run fine as long as there is some RPM's...but as soon as I idle, it does the surge/almost die routine. I can put it in neutral and rev the engine without issue...but immediately goes back to idle and starts again.

Any idea's? Im thinking fuel starvation related...ie, fuel pump or fuel filter...but I just replaced the filter a couple months back...
 
No water...just some minor mud and rocks.
 

That is great info Jon...but Im going to wait until tomorrow to check it out. Its cold as :censor: tonight with our first snow fall.

Question...how can romping on the gas rip the plenum? There is no moving parts...so unless just the massive pressure being sucked thru implodes it, I dont see how that could break...but again...Im asking because I dont know. :o

I did have a couple good moments of full "3Fe" throttle that day...
 
I'll be damned...couldnt take waiting...went out in my pj's with a flash light and checked and just plain as day, there is a large rip one ripple down from the TB.

This forum rocks!

Still want to know how hard wheeling can cause that to crack...
 
Its not neccesarily the wheeling per se, More that the part is 15 years old, order both and save yourself some heartache, in the meantime some duct tape will work for a day or two until the part get in.
Dave
 
There is movement involved. The air filter housing is bolted to the body and the throttle body is part of the motor. The motor mounts allow for movement and when in low range that movement can be significant. No question that age plays a part, but after 16 years those rubber parts don't owe you anything.
 
Back from the not-so-dead....

How much does a new intake tube cost from the dealer?
 
i could have told ya it was the intake hose. I had the same prob one time when I was wheelin. only mine kept dieing on a nasty section that I had to go through. I think I paid somewhere around $70 at the dealership at my cost.
u can get away with duct tape until you get a replacement. but be careful, most guys keep the tape for awhile. I know I didn't replace it for at least two or three months. :whoops:
 
i could have told ya it was the intake hose. I had the same prob one time when I was wheelin. only mine kept dieing on a nasty section that I had to go through. I think I paid somewhere around $70 at the dealership at my cost.
u can get away with duct tape until you get a replacement. but be careful, most guys keep the tape for awhile. I know I didn't replace it for at least two or three months. :whoops:

Yup. Last year, my original intake tube ripped right in half :eek:, so I "upgraded" to a silver-looking ricer-wannabe 15* elbow tube.

But, it's starting to leak, letting in unmetered air, causing my once happily running 3FE to run rough at idle. Again. :bang: Just not back to the point of dying, though. :whew:
 
Back from the not-so-dead....

How much does a new intake tube cost from the dealer?

If you call C-Dan, he will tell you there are 3 pieces. The part that connects from the MAF to the black hard plastic piece, the hard plastic piece and then the part from the hard plastic piece to the throttle body that everyone has problems with.

That part is right around $75 from Cruiser Dan. The other two pieces are in the realm of $40-50 each.

Duct tape is working well right now...
 
Back
Top Bottom