Roof Lights, D'OH

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 23, 2007
Threads
114
Messages
1,115
Location
Kennett Square, PA
Website
cruisin4parts.com
Ok, so I saved a bunch of money and built a roof rack. Good one too. I bought 4 KC 57 Series Rectangular lights to "light the day". The rack takes up the whole roof and the lights are mounted to the end of the rack, almost right above the windshield. I love the rack and the lights add a certain feeling to the cruiser.

Here's a link the lights: http://flickr.com/photos/claytongray/1222222547/in/photostream/

So, I tested them driving home the "long way" (through the woods) and used those bad ass lights.

The problem is is that they illuminate the windshield. I had some dust and mud speckles on the glass which became illuminated and made it very tough to see out.

Is this normal? Just get a car wash and hope for the best?
or
Do SOMETHING
I might be able to slide the rack a little bit back it might hold off the light from the windshield.
Any ideas?
 
I was thinking that. I gotta bring it back into the shop do that. Probably a little quarter inch tab would do it, eh?

This might be a good time to put a protective shield around those things. So much stuff hits stuff up there.
Anyone know the best way to way to cut steel mesh?
This stuff: http://www1.istockphoto.com/file_th...2/istockphoto_2097147_steel_mesh_close_up.jpg
 
is the light reflecting off the hood? if so you could look into a coating of some kind
 
I haven't figured out how guys make roof lights work, because I always got the same thing reflection back at me.

Moving the lights rearward so that very little beam hits the windshield will help some. But some light is going to reflect off the hood no matter what.

A super spot focussed light for long distance will work the best as less light will be diverted downward to your windshield or hood.

The problem is that any dust in the air in front of the windshield, at eye level, will become illuminated.

Otherwise, nothing beats mounting them up front, forward of the hood.
 
Like I said in my above post, my lights illuminate the entire cab....only when the sunroof is open.

98% of the clearcoat on my hood has peeled/chipped/floated off in some way or another, unintentionally resulting in less reflection. So, all I gotta do is close the sunroof and I can see damn near everything.
 
Yep huge problem for us or anyone that has lights that are overhanging on your windshield. Its a absolute must for us to keep our windshield clean.. when driving at night. Ive been wanting to make light shields for quite some time. That's really the only way around it... or move your rack back half a foot. Then the glare off the hood will be bad too:)

We use our overhead rack lights as a huge map light sometimes :)
 
The old-school solution is to black out your hood, or at least, the center section of it (see picture)
Princess at Fall Gathering - hard core run 2.webp
 
Blacking it out makes a difference? Wouldn't of though of that. I'll try moving it back some for now and then when I can get to the shop I'm going to try to make a lower visor.
There's no way of keeping my windshield clean.
 
If you can pull the rack back till the lights dont over hang the windshield and that will solve it for ya, i had the same issue with my full rack awhile back, if you want to test it cut some half circles out of carb board and tape them under your lights like a shield and you will see what im talking about
 
This was one of the reasons I went with a 5ft long rack instead of a 7ft one. Another way I've seen people handle this is to go pencil spots on the roof and floods on the front bumper with the pencil spots pointed above your normal high-beams.
 
I think I would make a light shield that extended in front of the lights and mounted to the same location. Make it extend just far enough to block light to the hood. Problem solved.
 
I was thinking that. I gotta bring it back into the shop do that. Probably a little quarter inch tab would do it, eh?

This might be a good time to put a protective shield around those things. So much stuff hits stuff up there.
Anyone know the best way to way to cut steel mesh?
This stuff: http://www1.istockphoto.com/file_th...2/istockphoto_2097147_steel_mesh_close_up.jpg


IMO i think you should make a visor for under the lights that spans under all the lights. like one continueous visor so no light gets through from the other lights.
as for the mesh... i was going to do the same thing but i thought they would obstruct too much light. so i did this...:cheers:

100_0550.webp

100_0575.webp
100_0550.webp
100_0575.webp
 
Moved the rack back 4 inches or so and made a big difference. Still a little light shines on the glass but I can see a lot better. I melted holes in my KC Light covers though!:doh:

I gotta get it into the shop and build a grille for the lights, and then a back bumper.
Oh yeah, and sliders.
 
Here is an idea:

Glare Shields

I realize you have rectangular lights but if you can fab a rack these will be super easy to whip together.
 
I just ran across this thread and thought I'd bump it up to current attention.

My first Toyota truck was an 1stGen '88 4Runner, and I remember seeing a lot of them with external visors along the roof/windshield edge. There was a version that actually had recesses for marker lights. They were called the MoonVisor IIRC. Non-lighted model was the SunVisor.

5828.jpg



I've always wondered why they never got developed for the 80-series. The additional protection from the mid-day sun beat down was great.

However, I think one of these would come in very handy with combating the windshield glare from the roof lights.

Thoughts, anyone?
 
Sounds like a a pattern problem, like some one else said you would be better off with a pencil pattern like the hella rallye 4000 offers or mount them higher and maybe even further forward.
 
Back
Top Bottom