Replacing Windshield

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 29, 2007
Threads
102
Messages
759
Location
S. Jersey - New Germany
I'm having my Windshield replace by an autoglass shop. Is there anything I need to know. They told me that they were going to try and save the old gasket when they remove the old glass.
 
https://forum.ih8mud.com/search.php?searchid=2143306 is the return from a search here for 'windshield replacement'. Tons of info. The short story is that the gasket, if original, will not be saveable. It is glued with urethane to the glass and window frame from the factory. The installer will be screaming bloody murder when he removes your old windshield, and will be very resistant to suggestions that he glue the new one in. If you allow him to install the new one 'dry', you will probably have leaks and squeeks later.

-Spike
 
If you allow him to install the new one 'dry', you will probably have leaks and squeeks later.

-Spike


The windshield will leak and squeak if the glass is not glued per the procedure in the FSM. The backglass also needs to be installed in the same manner or it will leak.

I watched the glass guy reinstall my windshield and backglass, after my re-finish, to make sure he glued them. He was not too happy about that but they don't leak.
 
Thanks guys, I thought I read about the sealant process before I just wasn't sure about using the old gasket. It sounds like I should hold off until I can get a new replacement gasket.
 
56121-60100, suggested list, $39.72.
 
I used new OEM gasket and a used LX450 glass. After no one would install "my" glass, I got Heckler over and we installed in in about an hour. That included the gasket sealant...
Funny part: I originally did not put sealant on the top part between the glass and gasket because "hey, it doesn't rain up does it". Well.... it whistled dixie due to air coming in... came back and promptly finished the job.

USE SEALANT
 
Should sealant be used between the gasket and the body as well?

Found the answer in another thread--yes, it should be.

My glass was replaced at some point in the past (says PPG in the lower middle) and I see rust bubbles starting along the upper right-hand edge. grrr.
 
Last edited:
I've gone through the FSM which shows were to use the urethane sealant. And I've talked with the installer and they do use a urethane sealant. I also gave him a copy of the RR instructions from the FSM.
 
WOW . . . . Just got my Cruiser back, in fact picked it up after work last night. I thought I could reach right through the windshield without touching glass. It's hard to appreciate how clear new glass is when your use to looking through 200K+ of micro chips not to mention the two bullet chips and the two small star cracks I had. It always looked like I had bugs on my windshield that wouldn't come off.

Thanks for all of the help. It definitely insured me getting the job done right. :beer:
 
Well it only took 5 days, my windshield took a stone almost dead center at the bottom between my windshield blades. Out of all the chips and stars I had in the old one this has already traveled about 8 inches. Oh well :mad: looks like this project will cost me 2Xs.
 
SUCKS!

Well, I bought a used LX450 windshield that I examined, examined, and then examined some more before buying. Right as we were finishing the install my girlfriend crawls into the drivers seat and promptly says "Is that a chip or dirt?" It was a chip! and it was summer so it immediately started spreading. I bought that crack sealer and it's been the of a pearl ever since. Sucked to have had to do this to a freshly installed windshield.
 
The previous owner had had the windshield replaced and it leaks really badly in both bottom corners, when it's raining and i'm driving, it constantly drips on your foot!!

I have now got a stone chip on the screen and will have to have the screen replaced I think, when he replaces the screen, do I have to tell the auto shield guy to glue the screen in?
 
The leaks are from not being urethaned properly when the glass was installed. It should have been urethaned to the body and then to the windshield. As per the FSM.


What do you mean "screen"?
 
He's English. Think 'windscreen'. :D

-Spike
 
Don't let it throw you if he mentions his bonnet.
 
Nothing at all wrong with my bonnet!!! :-) but I do have a chip in my windscreen LOL

My front bumper has some stone chips too, but my sun roof is fine.

I also get water in the boot of my car as well, but have read that is a common LC problem too. LOL


Sorry for my English being English :-)

I must admit when I write on here, I have to be soooo careful how I say things :-)
 
Back
Top Bottom