Rear Spray Nozzle - Removal?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Cannon88

In the duck blind...
Joined
Dec 7, 2009
Threads
94
Messages
2,217
Location
Ft. Worth, TX
Anyone know how to remove the rear sprayer nozzle from the upper hatch? I dont want to damage it by just ripping it off if there is a proper way to do it. Mine is a 93, but I assume they are probably all the same. I have searched, and I think this may be the one thing never covered on MUD. :D I also didnt find it in the FSM.

TIA :cheers:
 
is your's clogged up or just not working?

Mine was dribbling/clogged up. Used a small paperclip and gently cleaned the nozzle. Used a blower attached to air compressor and disconnected it where the tube is under the top of the liftgate. That blew the slimy crud crap out and it works great now. I didn't have to remove the nozzle.

Sorry if that doesn't help much.

Jon
 
When I bought the spare hatch the guy cut off the hose, so I have no way of connecting it to the truck. I have the good hose and sprayer on my current hatch, so I need to swap the entire assembly. I dont know why he just didnt disconnect the hose like he should have.
 
When i bought mine, sprayer was shaved off and I only had the hose between body and hatch. To pass safety inspection I had to put new one. So i didn't have the problem to remove it like you do (PO did it in a brutal way), but after i installed it i didn't realize that nozzles can be adjusted. Also i have a dent on my hatch where the sprayer is located and it was spaying wrong ways, so i thought that i had to take it out and fix the dent. There should be a holding clip at a back of the sprayer. Tilt your sprayer toward the back of a car and you should see that clip. I hope it helps.
 
How I remember the sprayer got a kind of a rubber seal between a hatch and a its own body. If you will try to push your sprayer to a side a bit it should be able to play a bit because of that rubber seal. By tilt i mean push it a bit toward a rear window until you gonna see that small clip which is holding the sprayer.
 
I've got an extra hatch I'm looking at. Once you remove the rubber grommet holding the hose (inside of the LC - hatch open), you can barely see the back side of the sprayer....it has a plastic clip similar to that of an electrical connector and what looks to be a small drop of RTV. If you can't insert new hose from that end then you'll have to try AKELLA's way....looks a lot easier to do with the hatch on the bench...
 
Akella, thanks for the tip - you were right about the rubber ring. I got it now! Here are some details with pics to show anyone that may need this in the future.


Here is a pic of the rear sprayer on the spare hatch I picked up for $75. (not bad for a complete hatch!)

RearSprayer1.jpg


I pushed the sprayer nozzle slightly to the side, and was able to get my tool under the rubber ring that is between the sprayer and the hatch.

RearSprayer2.jpg


Here is a pic of the rubber ring after removal.

RearSprayer3.jpg


This pic shows the sprayer nozzle still seated in the hatch. The two green arrows point to the 2 plastic clips that are keeping the nozzle from sliding out of the hatch. These need to be compressed for the nozzle to come out. There is not much room to work with, so it is harder than it looks.

RearSprayer4.jpg


And finally, the sprayer nozzle is removed.

RearSprayer5.jpg


Hope this can help someone else out.
 
Yes again, thanks for posting.
 
Hello. Good info here. I'm not trying to be an A--hole, but in your post #4 it seems all that was needed was the new little length of hose from truck body to back of sprayer? Did I miss-read. At any rate, good post if anyone else needs to swap theirs out or clean it.
 
Back
Top Bottom