Rear Heater Core

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 7, 2015
Threads
11
Messages
80
Location
ohio
I saw on another thread on here where the heater core lines were gunked and leaking under the passenger side door. We just got our 96 LC running after 3 years sitting from blown HG. Bypassed the heater so now I have no heat whatsoever. Can you tell me how much those lines cost and how much of a pain it would be to replace them? Don't want to do rubber line, wondering if we'll have to tear out the dash/airbag to replace those two pipes. Anyone else done all that without pulling tranny? Like I said it was just put back together from blown HG, so not about to pull that tranny. Any tips??
 
Last edited:
I understand they are not possible to get installed (in one piece anyways) with the transmission installed. I have removed the lines on both of my 80s, and even without regard for the lines themselves (they will NOT come out without cutting them) it was a miserable job - I have to imagine that installing them would be 10x worse. Personally, I'd just run rubber or silicone lines and secure them well.

I have read where people install new OEM lines, but have to cut them into sections and join them with hose. Personally, I'd much rather have a few feet of hose, no OEM line and only 4 clamps (2 per hose for the rear circuit) than have a few inches of hose, a few feet of OEM lines and 8+ clamps. Too many failure points for me.

If you still want to try it with new OEM lines, @cruiserdan would be a great source for pricing and parts.
 
yeah dont want to go the little bit of hose route since if it comes off or fails, there goes all the coolant all over the road and a LC overheating, saw enough of before the HG blew.
 
Please clarify the "Bypassed the heater so now I have no heat whatsoever." statement. If you don't have coolant going to the main cabin heater, plumbing the rear heater is going to be very difficult. The hoses are different sizes. The main heater hoses are 5/8". The rear heater hoses are 1/2".

I have my drive train out for an engine rebuild and I removed the rear heater including those steel lines. I can assure you replacing them without pulling the tranny and probably engine won't work.

Are they leaking now? Last summer I flushed the cooling system with Evaporust. I could see rust in the rear heater tubes. When I removed them they were clean.

Hope this helps,

Dan
 
The tubes are a serious PITA to replace properly! I removed my exhaust (diesel) and the heat shields and then cut the pipes out. I plan to use the space under the RH seat for OBA. Knowing what I know I would do the rubber hose route but, use MARINE hose, it is stronger and better protected and of a VERY high quality, it will be on your car long after most of it has disappeared in a pile of red dust, I used it on my fuel tank fill line and it is brilliant!

regards

Dave
 
Last edited:
The tubes are a serious PITA to replace properly! I removed my exhaust (diesel) and the heat shields and then cut the pipes out. I plan to use the space under the RH seat for OBA. Knowing what I know I would do the rubber hose route but, use MARINE hose, it is stronger and better protected and of a VERY high quality, it will be on your car long after it most of it has disappeared in a pile of red dust, I used it on my fuel tank fill line and it is brilliant!

regards

Dave
where do you get marine hose at?
 
We need slow down a bit. If you bypassed the rear heater lines only, then you should have heat from the vents once warmed up, if not you have other issues. If you bypassed both heaters, that would make sense.
 
Where do the rear solid heater lines start and end? What do I have to do to just bypass rear? Is this something where dash and airbag has to be ripped out?
 
I'm still confused. There is no heater core under the hood. You do not need to remove the dash to access the lines. Check this thread:

bypassing rear heater hoses?

Beno has the head off for sure and maybe the engine removed, but it shows what those lines look like, where the start and end.
 
Wait... These things have heaters??
 
thank you
I'm still confused. There is no heater core under the hood. You do not need to remove the dash to access the lines. Check this thread:

bypassing rear heater hoses?

Beno has the head off for sure and maybe the engine removed, but it shows what those lines look like, where the start and end.

Thanks for that! That's exactly what I was looking for, led me to a bunch more too. I was searching rear heater lines, rear heater core, and couldn't find much in photos, that was perfect.
 
full
IMG00349-20160323-0803.webp
IMG00350-20160323-0804.webp
 
The disconnected hose is the return line or "out" from the main cabin heater. In the 3rd pic, the lower leg of that u shaped pipe has a hose attached to another pipe that is the "in" line to both heaters. It has a tee built into it that connects to both the main cabin and the rear heater. That's what I meant in post 5 about just connecting the rear heater without connecting the main heater.

The "in" line must blocked off or you would have coolant squirting out of the disconnected hose in pic 2. Check this thread, post 4 and 6:

Heater Hose Diagram?
 
Back
Top Bottom