Rear axle noise question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 1, 2006
Threads
104
Messages
573
Location
North Jersey
In the past few days my rear axle has developed a whirling sound between 15-30 MPH sounds like loud mud tires. Above 30 I don't here it but slowing down under 30 and very loud around 15 I can't tell if its the rear diff. or the rear PS wheel bearing. The wheel bearings are not loose and have been repacked about 6K ago, and I didn't find any sticks or other debris stuck in the wheel because it sounds like a stick rubbing on the tire tread. I would appreciate any help as I'm going to take this truck on a 200 mile trip next week. The axle is a full floater.

Thanks
George
 
First thing is I'd drain it and refill it to be sure it's not low or old gear oil. Who did the work? If someone else could they have put things together wrong? 6K is only a few months ago.

Does the noise change if you swerve back and forth - a wheel bearing will change louder/quieter as they come under side load. Does the noise change with the brakes on/off? Parking brake on/off (these are totally separate brakes from the service brakes)? Rear driveshaft's rear CV joint loose when wiggled with the truck in N with parking brake holding it in place?

DougM
 
Doug

I did the work and the diff. is full with new Mobil 1 75-90. I'll try swerving back and forth but the noise has is very short duration and its not to loud but it wasn't there before. Doesn't sound like brake noise I looked at the rear pads and they still have meat on them and it does not stop when I hit the brakes I'll try the parking brake but that doesn't hold unless its pointed at the sky. The u joints are all new. If it was the diff. or wheel bearings wouldn't it get louder the faster I drive?

George
 
Lock the center diff and remove the rear drive shaft to eliminate any drive train causes.

If the noise goes away, then it's likely that it's your driveshaft.
 
The noise seems louder still 30 MPH and lower, and dose not change while swaying the truck. I cannot get the center diff to lock when I push the button no light or ABS light. Is my transfer case toast?
 
The noise seems louder still 30 MPH and lower, and dose not change while swaying the truck. I cannot get the center diff to lock when I push the button no light or ABS light. Is my transfer case toast?

Do you hear the double click? (One inside the cab, one from the CDL motor.) Does the light flash?
 
Do you hear the double click? (One inside the cab, one from the CDL motor.) Does the light flash?
No relay click, flashing light, or motor noise from the actuator. I last used the center diff. while wheeling on Labor day my guess is its still slightly engaged with a fried motor.
 
Someone on this forum told me to use a water hose to narrow down my drive train noise. It helped me alot. Good luck with finding your noise.
Noise.webp
 
No relay click, flashing light, or motor noise from the actuator. I last used the center diff. while wheeling on Labor day my guess is its still slightly engaged with a fried motor.

Have you had the dash apart since then? It wouldn't be the first time someone forgot to plug the switch back in :D
 
UPDATE:

I took the rear DS off and the noise is still there but not as loud I guess the DS can amplify the sound or put more stress on the failed part IMO being either the transfer output bearing or rear pinion bearing. Where do I go from here? How do I find out if its the 3rd or the transfer? If I pull the axles out and its gone its the 3rd right? Without pulling the 3rd out how would one know if its the pinion bearing or the others inside. About 6K ago I had a shop install a new seal and crush collar before I retrofitted this elocking 3rd into the truck, He didn't charge me and said it all looked fine. :bang:

George

 
Back
Top Bottom