real time question - v8 position

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 18, 2005
Threads
44
Messages
300
Location
Seattle
I am re-doing the motor mounts we did 15 years ago.

Is it more important that the motor be centered in the vehicle or the t/case outputs in line with the pinion?

We used to have the outputs centered and the motor offset. I think it should be centered and let the drivelines be what they be.

Thanks.

awp
 
most of the conversions i have seen place the V-8 about an inch to the drivers side. thats how mine was done by the PO.
 
Before you center it, make sure the exhaust on the driver's side clears the steering gear. It's a tight fit with some exhaust manifolds and headers. My headers rub, and I'm going to need to correct that.
 
mine sits 1" to the drivers side, this helps clearence with the front driveshaft, i have plenty of room to clear a 3" exhaust if needed w/ramshorns and walker pipe.. I was worried that my rear driveshaft would vibrate considering the 2+" difference, but the mini CV i put in seems fine!
 
I am just about done with the motor mounts and the rear transfer mount. I have a couple concerns now.

1) the rear cross member is in the way to fit a CV driveline. Not really that big of a deal to move it. But it's another task on the list.

2) I changed directions mid build and put in a 465. This changed the angle of the drivelines and now my rear rotated housing is not pointing right at the the output. I think it's off by about 2 degrees.

3) The working angle of the 85 CV joint is just about maxed out at ride height. I expect 10" of downward in the rear so this will really be a problem. The rear driveline is about 27.5" long.

4)Since I changed the motor mounts, I set the motor dead level left to right and front to back. It seems some are nose up, but my thought is that that only exagerates camber issues.

any thoughts? I'll post in hardcore too.

awp
 
pbgbottle said:
doesn't the engine need a few degrees of angle for the carb to sit level or something like that ,also

cv joint modification link may help ya here

http://www.4x4wire.com/toyota/tech/cvmod/
Sort of. Actually the maifold is angled to allow the carb to sit level relative to the angle the engine is at.

Most V-8 applications have the engine installed at an angle, so the most common monifold pattern is with an angled carb base.

Some installations have the engine level. A classic example are the 1961 though 1963 Ford Thunderbirds. The car is so low that the engine is not angled but is parallel to the ground. Ford has special manifolds cast up that took this into consideration. Their carb base or bases (some were 3x2) were set flat instead of angled. Ford had these manifolds specially cast because the lower bases in the rear forced vacuum bosses to be moved elsewhere.

However, and I'm getting to the point of all this, it is possible to machine a manifold flat for a special application, provided you are not machining into a vacuum or EGR boss at the rear of the carb base.

One slight problem is that the carb studs will not be exactly perpendicular to the base. There are three ways around this. One is to machine new stud holes in straight using Helicoils. This is difficult because you are narrowly changing the angle, and machine tools like to follow the path of least resistance. Or you can make or use a baseplate adaptor that uses upside down bolts to attach the carb. The adaptor can use the alternate set of holes in the manifold. Most of these adaptors change from square to spreadbore pattern, but can be altered to match your application. Or you can make one from a solid piece of aluminum if you have the machine tools. The last method is to be very careful with the pressure the nuts are cinched down with, because they are at an angle to the carb base flanges. This would be an area where a thin washer followed by a lockwasher and then a nut would work, if not cranked down hard. I have seen carb base pads milled for this angle, but if you ever went to sell the carb at a swap meet, altered carbs often turn off potential buyers, and they void warranties.
 
Back
Top Bottom