Real time help - won't start!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 30, 2006
Threads
1
Messages
10
Location
Holt, MI
'97 LX450 4.5l factory lockers.

Its been running just fine. I drove it to work this morning and ran an errand a few hours later and everything was fine. I go out to run annother errand and it turns over but won't even try to fire.
The only problem I've ever had with this truck was 2 mornings in the last month when it was REALLY cold it started fine but felt like it was running on just 5 cylinders. After it warmed up for a few minutes everything was back to normal - the last time it did this was 3 days ago. I figured that I need to do a mini tune-up (plugs, wires, cap, rotor) but have not had the time to do so yet (expect a call Dan).

Any ideas? I bought it used and only have the 1 key that I always use (dealership asked).
Even a temp fix just so I can get it home to my garage so I can take a good look.
HELP!!

Thanks.

Ron
 
Hmmm. First guess would be the EFI fuse under the bonnet but you've checked that so.... check it again. :D

Next would be coil wire, dizzy (rotor), and maybe the Fuel Pump Relay. Try starting it with the accelerator to the floor.

-B-
 
Last edited:
When you mean won't start ........ does it mean the engine just keeps on turning or nothing at all?


Oooppss it read it............ Just keeps on turning...........

ditto on the EFI fuse
 
IIRC, there was another member with a similar problem. Checked the wires and all, but didn't notice the tracking on the inside of the dizzzy... so while you're in there, make sure the inside of the dissy is clean. I'd also check that the rotor is not tracking too.
 
The cap & rotor are a little old, but fine. When the key is turned on I can hear the fuel pump come on for a couple of seconds so I think the EFI is OK.
Since pulling the coil is a minute's work I took it down to AutoZone and they say its OK.
I didn't have time yesterday but tonight I'll pull a plug to verify its getting gas.
I think its in the spark, but I don't know...
Any suggestions? Do the crank triggers on these go bad? Its only at 120k miles.

Thanks for any help.

Ron
 
Think either fuel or spark - Can you smell fuel after a few tries? Can you run your lights and sound your horn and it sounds full strength?
 
As much as I hated to, I pulled it over to the dealership as I just don't have time to chase down electrical gremlins right now.

First time ever for dealer service and they SUCK! I dropped it in their lot Sunday evening and called Monday morning to make sure they got the keys. 4 calls later (to them, never from them!) and they tell me (Tuesday afternoon) that I need a new motor cause the timing chain failed - $4500!?!?!?!

I asked how 4500 was justified for a timing chain repair - then he says that my cam is broken too. Needless to say I told them to immeaditely stop touching my truck and that I would pick it up tonight.

Anyway, anyone have an idea on parts costs? I called and left Dan a message but he's not in today.

Thanks for the help.

Ron

PS In case a valve punched a hole in a piston are there any used 4.5's in the lower Michigan area?
 
Tough luck Ron. :frown:




From this.....

bbm715 said:
The only problem I've ever had with this truck was 2 mornings in the last month when it was REALLY cold it started fine but felt like it was running on just 5 cylinders. After it warmed up for a few minutes everything was back to normal -

To this .....

I need a new motor cause the timing chain failed - I asked how $4500 was justified for a timing chain repair - then he says that my cam is broken too.

Something is missing in there. I would think a timing chain problem that caused a broken camshaft would make a rukus and not just a rough running engine that got back to normal in a few minutes.

Any ideas on the service history? Oil changes? Prior repairs? Any unusual noises leading up to this?

$4,500 for a "new" engine would be a pretty good price though. I would assume they need to do some type of head work if the cam was busted. That might be ~$800 'Mud price on a new short block is ~$2700. That leaves only $1,000 to R&R the engine and bolt on all the old bits. A completely new long block is probably >$9,000.

I think there is a company in Texas (Thunderbolt or Thunderbird or something like that) that sells rebuilt 1FZ-FE engines. You might give them a try. I wouldn't be happy with a bone yard engine in my 120k mile LX450 but you might come out OK.

-B-
 
The $4500 was for a used running motor. New, I might have done it but something pulled out of a junker just didn't thrill me.

Once I get it home I'll tear into it to make sure that a cam is indeed broken - actually, if the timing chain is off then I'll probably pull the entire head anyway to make sure nothing got knocked around.

Makes me wish I'd insulated and heated my garage this past summer instead of waiting and going with a new motor for my M715 - Oh well, hindsight is indeed 20/20.

Ron
 
Back
Top Bottom