Real time - front diff removal

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 22, 2003
Threads
21
Messages
514
Location
VA
:confused: I'm having trouble getting the fron diif out of my front axle.

So I have my locking front axle on jack stands, both axles are out and all the nuts holding the diff to the axle have been removed. I can pull the the diff out between a 1/4" to 1/2" and then it stops. It appears to be catching on the right side behind the locking actuator. Any help is appreciated.
 
Is the axle still in the truck or on the bench? So long as the axle is locked it should come out. When you try pulling it does it feel/sound like it is being held up by metal on metal?
 
The problem appears to be that the axle is not locked and it is not on the truck. It was taken off after the truck was in an accident the slightly bent the front axle.

How do I go about locking tha axle now?
 
Are you sure you got all the nuts off the studs, including the two or three that go through the locker actuator housing?? Those held me up till I realized they were going all the way through locker housing and into the axle housing.
 
Are you sure you got all the nuts off the studs, including the two or three that go through the locker actuator housing?? Those held me up till I realized they were going all the way through locker housing and into the axle housing.

Yes, I can pull the diff away from the axle and have a gap of 1/4" to 1/2" all the way around the housing.

From the other post and the FSM the locker should have been locked so I think that is what is causing the interferance. I'm trying to figure out how to unlock the locker when the housing is off the truck and the axles have already been removed.
 
You will have to power it up in the manner the FSM outlines for testing. You may also need to reinsert the RH shaft in order to use it to rotate the side gear to get the dog clutch to line up.
 
Why would you have to power it up?

Take the locker cover off, take the gear out. push the locker actuating rod in with finger pressure while rotating an axle (reinserted to mesh with the side gear) When the rod moves in, it'll be locked.

That works too. I was just thinking of retaining the proper "clocking" of the actuator. Maybe it doesn't matter.
 
Thanks for all the help. What would I use to power the actuator with. I believe the FSM says to use a dry cell battery. That to me :banana: means not a regular car battery.

I was going to try Grumy's idea of taking the actuator off and trying to move things around but I can't get that off either. I have the three nuts/bolts that hold in on off but it won't budge.

This diff will be a spare or eventually sell it becaue the axle housing is bent. I have to admit I'm don't know what you mean by clocking. If this diff is never going back into this axle do I need to make any marks?

Dan since I replaced this axle with a used axle I'll be ordering rebuild parts in the future so your dogs won't need to worry about going hungry.
 
I think the FSM calls for a 9V battery like in your smoke detector.

The three bolts on the actuator cover have 10mm heads. A few taps on the cover with a small hammer will loosen it up enough to get it off.

The bolts that hold the actuator itself won't let the actuator come off until the gear is out.

If you want the actuator to work again properly, you need to put the gear back in the exact way it came out. It will go in lots of different ways. You need to mark it's position with a sharpie so you can put it back correctly.
 
This may be a dumb question but if the axles were removed and the locker not locked wouldn't the one dog fall into bottom of the axle housing? Just wondering out loud. So the goal then would be to just move the shift fork, correct? You'd still have to follow the above info to get it to move.
 
Back
Top Bottom