Question about installing a car amp

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 2, 2006
Threads
70
Messages
335
Location
Seattle, WA
Website
www.bladerunner80.com
I was doing some searches to see how people had wired car audio stuff in their FJ-40's and I had a question about wiring an amp in. The PO did a "Painless" wire install and I found an unused power lead for the radio, I was wondering if this lead is alway hot or if its switched with the ignition? I was thinking it would be good spot to splice the "power on" lead for the amp. My amp will just barely fit in the tool box, so it should be nice and secure, I've also have a couple boxed 6x9's that my dad gave me out his old el camino that should mount nicely to the roll cage. Instead of running a head unit, I think i'll just pipe a head phone jack into the dash and run my iPod and XM off of it. Guess this will be my next task after I rip into my brakes this weekend!

Thanks!
 
first- hook something up to the wire. (test light, meter, old stereo, amp, etc.)
then- ground it appropriately
with key off- see if it lights up.
turn the key on- see if it lights up.

If you know that it was meant for the stereo it is probably ignition switched, but oftentimes there is a constant power wire to the stereo as well as a switched, usually just on newer vehicles, to save digital presets and stuff, but where this is an aftermarket wiring harness, who knows. easier to check it now, then to speculate, and end up with a dead battery later
 
Yeah good call. I was going to test it tomorrow, my damn test light from Sears fell apart on me, looks like I'll have to go and get a new one. Hopefully I can get this thing hooked up soon, it would be nice to have some music to listen to every once in a while.
 
Toolbox

You might be careful installing the amp in your toolbox....
If it doesn't get enough air flow you could burn it up.

Just a thought

Good luck with it!:beer:

Thanks![/quote]
 
Pin_Head said:
First thing to do is look up how many watts it uses, then divide that number by 12 to get the amps it will sink. Then look up the gauge of the wire you want to hook it to and see what its amp capacity is.



X2, amps draw more power generally then a standard wire can handle. be sure of power draw like pinhead says, or you will melt the wire and possibly burn up the amp. also they do need to air to cool.

just my .02 worth ..


Good luck ... :cheers:
 
Yeah, I wouldn't run the amp's power off of the radio lead. All I would use the radio lead is for the power "turn-on." The amp uses it to sense a power connection, then turns its main power on (which will be a heavy gauge wire connected directly to the power with an in-line fuse). This keeps the amp from running all the time and draining the battery. Usually people just tap into a power antenna lead, but since crusiers don't have them, I'm kind of stuck looking for a switchable power source. I figured tapping into the radio lead (if it's switched) would be the easiest route.
 
I was just talking about the tool box idea and cooling with a guy I work with. I'm thinking I might cut a vent hole and then cover it with some type of wire mesh grill material to make it look nice. I figure I could replace the lid easier if I decide to ever remove the amp out of the tool box.
 
that was what I figured, that you were just looking for an ign switched lead, I think most amps run off a big wire and just use the ign one as a trigger. cutting a hole might not be sufficient, but a computer fan will work just fine on 12v, and they draw almost nothing, so you could use that same trigger wire to power one, hell they are easy to find and easy to mount.
 
I don't know what year 40 you have but since your talking about your under the seat tool box the ignition switch should be on the dash (easy to get to) and not the steering column. On the back of the ignition switch you should have a terminal for accessories. This is the spot where I wire my radios up to. It allows you to use your radio while the vehicle is not running without leaving the switch in the on position. Just remove the switch and there should be four terminals on the back. One will be hot all the time, one is the run lead and another is the starter lead. The fourth one may not have anything wired to it and should be marked something like ACC. This terminal is hot when the switch is turned counter clockwise and when the turn is turn clockwise to the on position. This is how most radios are wired. Modern ignition switches the first position is the accessory position, then on and start. Toyota must have used the same ignition switches in the cruiser as they did in their cars because all my old cruiser have had the accessory terminal even though Toyota didn't offer a radio in a cruiser until the 1973 model.

John
 
Well, I got in their with a voltage tested last night and found a bunch of good spots to tap into. The PO mounted the new wire kit fuse block in the glove box, and there are a bunch of spare leads (power windows, int. light, radio) and also a second ing. switch lead (I'm guessing this for the spare fuse block you can buy from SOR for more accessories). Tested the radio wire and it should work with no problems. Think a 30 amp in-line fuse is good for a 300 watt amp? Good idea on the computer fan, that would probably do the trick, then I would have to hack the lid to the tool box apart (it would need a pretty big hole). But a small computer heat exhaust fan would work perfect.
 
check radio shack for the fan, they sell small ones for this type of stuff. my buddy got one from them for the amps in his 64 FJ40. just dont forget you probably will need an air intake hole and then the exhaust for the fan. you could do several small holes for the intake to give more flow over the body of the amp to cool it and just the one exhaust hole. just a thought, good luck!!
 
I have the Painless, and the grey/black radio lead should be switched. There is a red one that is hot all the time, but the grey/black one is switched. HTH
 
Back
Top Bottom