Polyurethane Engine and/or Tranny Mount???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 21, 2004
Threads
374
Messages
5,499
Location
San Diego
Website
youtube.com
Hey Guys

Anyone know if someone makes ultra stout engine and/or tranny mounts for the 80?

I know about the increased vibes and such, but this will be a race truck seeing A LOT of abuse

Thanks
 
Kevin,
Do you think the added stiffness of poly would possibly put stress somewhere else and eventually cycle enough to break running Baja? -just throwing that out there, I have no idea-

what about getting new OEM mounts, think that would be good enough?
 
Hey Guys

Anyone know if someone makes ultra stout engine and/or tranny mounts for the 80?

I know about the increased vibes and such, but this will be a race truck seeing A LOT of abuse

Thanks

I had an e-talk with someone at Energy Suspension awhile back
looking for polyurethane bushings, mounts, etc;

They do not make any (yet) specific for the 80 series;
some of their stock sizes may fit like sway bars, end links,
but that is about it.

However, the contact said that they may consider making up bushings if they could get an 80 to work with for a few days.

If you live near San Clemente, CA give them a call,
and keep an eye on their website.

Their urethane is not rock hard, and holds up much longer
than rubber.

Another route would be to surf Australian websites;
seems like a lot of aftermarket stuff comes out of there.

G
 
Last edited:
I have used engine torque dampers from both Weapon R and Ingalls Engineering with really good results. If your on & off the gas it takes the punishment out of the motor mounts. It is essentially a small shock with an elastomer stack inside. You can adjust preload on the shock. It is something I have planned in the near future. Don't bother trying to find the right application for the cruiser, just call them and ask for advise (and a sponsorship) in finding a good universal length. Build your own brackets. It is really easy. These are nice because you don't have to put up with the bad vibes from the Urethane mounts. Just an Idea. -Andy:D
Stiffy-description (Small).gif
 
Last edited:
If you can't find a specific aftermarket hi-po HD mount, you can modify the stockers to better cope with the stress. This can be done with a couple pieces of C channel... I'll dealve into that more if it interests you. Another option is to go into the Toyota parts bin and look at other mounts to see if there is anything else that might fit the bill..... say, the Tundra 5.7L 4x4 is bound to have something a tad beefier, and it might bolt up, or have minimal mods to get it to.
 
Are there a lot of known issues with the 80 motor mounts? The Jeep world has had mixed success with poly motor mounts - poly is always more prone to crack and self destruct then rubber. It is a choice of "bend but don't break" vs. "shatter if you push it too far".

The best solution ended up being a stock leaf spring bushing (rubber) in a modified mount. In other words, beefier rubber. I'd look at potential Toyota solutions as recommended - maybe modifying the new Tundra mounts that have to handle all that torque before I'd want poly.

But then I'm really not a fan of poly. I've just never seen it hold up well in any abusive application over time.
 
Are there a lot of known issues with the 80 motor mounts? The Jeep world has had mixed success with poly motor mounts - poly is always more prone to crack and self destruct then rubber. It is a choice of "bend but don't break" vs. "shatter if you push it too far".

The best solution ended up being a stock leaf spring bushing (rubber) in a modified mount. In other words, beefier rubber. I'd look at potential Toyota solutions as recommended - maybe modifying the new Tundra mounts that have to handle all that torque before I'd want poly.

But then I'm really not a fan of poly. I've just never seen it hold up well in any abusive application over time.


I agree that some of the "old tech" polyurethane was hard as a rock;

the new stuff that most companies are making is much better;

Go to Energy Suspensions website and look it over;

http://www.energysuspension.com/pages/hyperfl.html

They make polyurethane mounts, bushings, etc for a lot
of high performance vehicles that have a lot more
power than our LC's. They just don't make anything
specifically for 80's, yet.

About 15 years ago I put some polyurethane spring bushings
on my FJ62; they are still in perfect condition and the vehicle
tracks like it is on rails.

Check out the site.

G
 
Back
Top Bottom