pinion still leaking

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 4, 2006
Threads
636
Messages
23,858
Location
Buckley, WA
Changed the pinion seal and it is still leaking..... i'm thinking maybe I pushed the new seal back to far. FSM says only 1 mm and I'm pretty sure I went further back than that. Anyone else had this problem??
 
what kind of groove are you talking about??

i didn't see anything strange about the flange.
 
Last edited:
what kind of groove are you talking about??

i didn't see anything strange about the flange.

Over time, a shallow groove can form on the machined surface of the pinion flange where the pinion seal rides. Even if you replace the seal with a new one, if the seal placement is over the groove, the pinion will still leak. It can sometimes be remedied by installing a Speedi Sleeve or by replacing the pinion flange.
Similiar to this:
attachment.php


Other things to look for are evidence that your outer pinion bearing shims have spun. If the shims have spun along with the bearing, they can be worn down to a point where the preload is out of spec allowing movement of the bearing and shaft. This slight movement will force oil past the seal.
 
thanks i'll look for the groove...... how many bananas is it to replace the shims/bearing??
 
The diff has to come out to do it right and you have to be able to set-up the backlash and pre-loads. Diff set-up is best left to someone who does them often.
 
When you take the tailshaft off the companion flange, is there oil there?
We get oil leaking down the splines on trucks occasionally. You may pick it if you look at the flange closely.
Hope this helps

Matt
 
The diff has to come out to do it right and you have to be able to set-up the backlash and pre-loads. Diff set-up is best left to someone who does them often.

crap :frown:
 
ok pulled the flange off and there does appear to be a groove on it

(I apoligize for the pictures but my fiance has my camera and I can't figure out how to use my sisters camera for close up settings)

DSC02060.jpg

IMG_0057.jpg

DSC02060.jpg


looks like i could use a new one, yes?
Dan how much do these things run??
 
We stock these yokes for that reason

That is why we stock them. most yokes are grooved when removed and often overlooked. $40 is cheap insurance that it wont leak. Dan is right, the best way to replace the seal is to do a full tear down. At that point we usually install our solid preload spacer, so if you ever have to change the seal again, it can be done easily w/o ruining pinion brg. preload.
 
Wish I could afford a complete tear down and rebuild. I plan on doing that when I get it regeared next year. With the wedding and the 3000 mile move comming up i'm on a tighter budget that a college kid. (I don't even get any water for my top rahmen)
As long as I can get it to stop leaking till I get to charlotte i'll be happy for now.
 
If this were my truck, I would inspect the upper bearing shims. If they look OK I would get a new flange and nut. Speedi Sleeves are cheaper but in my experience, they don't work real well. For a relatively inexpensive part like a flange, it is better to replace. There are several vendors here on MUD that sell them. I would replace the seal again along with the new flange. The pinion nut needs to be tight. It is sometimes difficult to attain the proper torque specs. Once it is tightened the nut needs to be staked.
After replacing the flange and seal pay close attention to any abnormal pinion play, excess backlash, vibration or sound from the rear. If there are no more leaks and everything else with the diff appears OK I would call it good and run it. If it stills leaks or there is anything else that doesn't appear normal I would do as Dan suggests and tear it down and send the diff in for R&R.
 
Back
Top Bottom