Panard rod

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 20, 2007
Threads
17
Messages
55
Location
Christchurch, New Zealand
Hey all,
I have a 4'' lift on my Cruza and I was looking at my truck and I noticed that the diff's sit slightly off to one side. I knew I would have to address the problem some time :D
I tried to get hold of adjustable panard rods from a few places today but no joy! Hey its only the first day of looking:crybaby:
Has anyone made panard rod mount modifications?
I was thinking about lowering the mountings.........
Any ideas.....?????
 
Hey all,
I have a 4'' lift on my Cruza and I was looking at my truck and I noticed that the diff's sit slightly off to one side. I knew I would have to address the problem some time :D
I tried to get hold of adjustable panard rods from a few places today but no joy! Hey its only the first day of looking:crybaby:
Has anyone made panard rod mount modifications?
I was thinking about lowering the mountings.........
Any ideas.....?????


Yes MAF, I was going to use it for the rear panhard on my truck. I thought it would work better and it was about $100 cheeper but they stoped selling them.
:cheers:
 
Yes MAF, I was going to use it for the rear panhard on my truck. I thought it would work better and it was about $100 cheeper but they stoped selling them.
:cheers:

no kidding, I have the drop bracket for my rear and personally think it's the best solution. Too bad they discontinued it, it was the only bracket they made that made any sense to me.
 
I have adjustable panhards, there is a drawback that I didn't forsee. If your panhard is at an angle from lift, at compression the axle is pushed over towards the axle-mounted end. This makes the tire on the driver's side hit the frame on compression. To get the least amount of frame rub, you have to adjust the axle to be off-center at ride height- probably pretty much where it's at with a stock panhard. The drop bracket to get the panhard level is probably the best option.

-Spike (Freaking geometry- I thought I was past all that.)
 
no kidding, I have the drop bracket for my rear and personally think it's the best solution. Too bad they discontinued it, it was the only bracket they made that made any sense to me.


I agree 100% with you Rick! I went with the MAF drop panhard bracket too as it made sense. The usual "twist" a lifted 80 has when crossing things like railroad tracks at speed nearly completely disappeared! I won't get into the drop bracket debate but I will praise the rear panhard drop all the way! Flat panhards are happy panhards!
 
Raise the axle end if you rock crawl. I did the MAF bracket, and it drops way too much during full compression, and you are lowering the roll axis (plus it is near impossible to get properly aligned as the stock mount may bend a bit during nut tightening, which shifts the alignment - unless you get a bit lucky you are going to be doing an adjustable panhard anyway). Raising the axle end will require custom fabrication, but it would be very simple and the best solution out of all of them, but don't raise too much or it will hit the frame under full compression.

Easy solution? Drop $250 on the MAF 4+ rear panhard with spherical joint on one end. You keep rubber for noise isolation on one end and get the rigidity and unrestricted motion of a spherical joint on the other. You do get a bit of side motion on compression on a 4" lift, but the link only increases about 1/4" (a squared + b squared = c squared where a is original panhard length of 42", b is lift height of 4", and c is the required length of the new link) on a 4" lift, which is nothing to write home about in terms of side to side movement on full compression at speed.
 
recycled metal version

this is as level as it gets with 7.5" of suspension lift, nothing getting hit up top with shock compressed fully, frame mount still stock. As mentioned above, that's a defective receiver hitch mount tube and the correct tubing that fits inside of it. Stock bolt goes through it and it's welded along the edges to the stock mount.
rear panhard raised mount.webp
 
Nice job, that's the plan that I have for mine, but will add a brace to the link tower. Pretty simple build, don't see why one of the vendors doesn't make one?
 
If people want something like that, I can probably get something together. But I think most would prefer a bolt on solution if possible.

Let me know what you guys think and when I get home I'll take some measurements and draw something up. I'm meeting with my fab guys anyways so I can get there input on it by this weekend.
 
...But I think most would prefer a bolt on solution if possible...

Making it bolt on would be relatively easy; Put a spud tube at the lower stock bolt location, so that the bolt doesn't crush the mounting point. Then make a brace over to the upper link mount that bolts to it using a couple of the stock holes. Bolt on would work well for most, the more hardcore could add some weld to make double sure.

My thought is about 2/3 of lift hight, ~3" for my 5" lift. I haven't pulled the springs and compressed the suspension to see how much room there is before contact with the frame, etc. It's been too damn hot.:crybaby:
 
we experimented with it just being bolt on and it's just not robust enough or worth all the trouble trying to engineer it to be. My advice is pretty similar to Tools...use a bolt welded onto the bottom to attempt to control the lateral forces and utilize the two existing holes located laterally to the stock mount. However, that plate is relatively thin and not a lot of metal. The lateral forces, even on the street from taking corners and on the highway from big sweeper turns, were enough to move it from side to side. At some point it just becomes a whole lot easier to commit to welding the whole enchilada up with some serious 0.25" plate and tubing so you know it's not going to move or break.

Making it bolt on would be relatively easy; Put a spud tube at the lower stock bolt location, so that the bolt doesn't crush the mounting point. Then make a brace over to the upper link mount that bolts to it using a couple of the stock holes. Bolt on would work well for most, the more hardcore could add some weld to make double sure.

My thought is about 2/3 of lift hight, ~3" for my 5" lift. I haven't pulled the springs and compressed the suspension to see how much room there is before contact with the frame, etc. It's been too damn hot.:crybaby:
 
this was our version

Rick, this is what we attempted. The lengths will obviously vary depending on precisely how much lift each has on the rear axle as they are currently outfitted. Making them this way would probably be fine on the street but welding it would be a necessity for off-road IMO.
rear panhard bracket copy.webp
 
we experimented with it just being bolt on and it's just not robust enough or worth all the trouble trying to engineer it to be. My advice is pretty similar to Tools...use a bolt welded onto the bottom to attempt to control the lateral forces and utilize the two existing holes located laterally to the stock mount. However, that plate is relatively thin and not a lot of metal. The lateral forces, even on the street from taking corners and on the highway from big sweeper turns, were enough to move it from side to side. At some point it just becomes a whole lot easier to commit to welding the whole enchilada up with some serious 0.25" plate and tubing so you know it's not going to move or break.

I agree to a point, but think it could be made to work. If the brace is a simple tube it will flex and the force on the link bracket will be more push-pull, not good, the link bracket's weakest direction. If the brace is made more robust, triangulated, gusseted, etc the force on the bracket would be more up-down, probably well with in the link mounts capability. Also, shorter bracket ~2-3" will have a fraction ~1/2 of the leverage, force on it, as a tall one like the one you made.
 
Back
Top Bottom