OME too short?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I ran Golden Spike with Bruce Miller in his OME equipped '40 years ago. '98 IIRC. He inverted the rear spring shackles about 10 times or so. I was walking most of the time so I carried a crowbar and would hollar at him when I saw it. He'd jump out with the tire jack, I'd slide under the rig and we'd have it re-flipped in a couple of minutes. It was still a PITA.

It is not the centering in the wheel well that concerns me. Never even paid any attention to that aspect. It is the inverting under flex that I can't abide by, as well as the stiff ride that the shackle angle contributes to.


Mark...
 
Last edited:
Tigerstripe40 said:
...The springs are arched, so as the tire moves up, it will also move backwards a little.

If you are looking to have the tire centered in the wheel well when the truck is sitting on flat ground, you will have problems with the tire moving backwards and into the rear quarter panel....

Exactly...

The spring arcs on the front pivot, and as James points out it moves back as it flexes. If you asthetically center it, your going to have bigger issues with it hitting your rear quarters. Sure this is an easy fix for those willing to trim their openings, but many are not. They just want to bolt on the suspension and go...

Here's a prime example of the read quarter interference...
attachment.php


As for the improper shackle angle, I will admit that a truck with a freshly installed suspension might have a rather vertical shackle angle, however when the suspension begins to "break in" the angle will pan out. OME designs their suspensions to be ideal when they are broken in versus other manufactures that boast of their suspension when they are newly installed. The net result is a sagging suspension after the spring is truly.
 
Mark W said:
I ran Golden Spike with Bruce Miller in his OME equipped '40 years ago. '98 IIRC. He inverted the rear spring shackles about 10 times or so. I was walking most of the time so I carried a crowbar and would hollar at him when I saw it. I'd jump out with the tire jack, I'd slide under the rig and we'd have it re-flipped in a couple of minutes. It was still a PITA.

It is not the centering in the wheel well that concerns me. Never even paid any attention to that aspect. It is the inverting under flex that I can't abide by, as well as the stiff ride that the shackle angle contributes to.


Mark...

I'll assume he was not running the OME anti-inversion shackle OR the anti-inversion plates for those not running the OME shackle? Inverting a spring is a risk of having a flexable spring, limiting its occurance with the use of a AI shackle or plate is the key....
 
One rig that I dealt with had at least 20,000 miles on the OME springs. Including a run from Ga to Ak, fully loaded to the roof for a houshold move. No improvement. :(

I like OME springs. To be honest I like them better under a wagon than a '40.

I think that the fact that the axle moves backwards a bit under compression is a given and I would assume well understood by everyone. But the negative impact on the ride and flex, and the shackle inversion situation is another story. :(

My suggestion is to go ahead and stick with the OME springs if that is what you have or what you are set on. I really don't have any other springs I can point to ansd say "these are better". If you have the poor shackle angle that all of the OME'd FJ40s that I have dealt with have, then buod a set of articulated shackles which will address the shackle angle "ride quality contribution", prevent inversion and add more droop to boot.


Mark...
 
cruiseroutfit said:
I'll assume he was not running the OME anti-inversion shackle OR the anti-inversion plates for those not running the OME shackle? Inverting a spring is a risk of having a flexable spring, limiting its occurance with the use of a AI shackle or plate is the key....


He did not have anti inversions, just standard shackles which came with the OME system. But being as how that is what was sold to him as a package, he should have been able to expect it to function correctly. :(


I have to differ with the position that inversion is a risk with a fley spring. I own, and have built several other rigs which will max out 14 inch travel shocks with leaf springs. No risk of inversion whatsoever. The key is a properly sized (length) and located (shackle hanger location) shackle for the spring.


Mark...
 
Mark W said:
He did not have anti inversions, just standard shackles which came with the OME system. But being as how that is what was sold to him as a package, he should have been able to expect it to function correctly. :(

Understood, though it is important to note that OME does sell standard shackles, and they advise using the anti-inversion plates for those that do... There are alot of shops out there selling OME springs without the matching shackles, and I can see how this causes problems...

Mark W said:
I have to differ with the position that inversion is a risk with a fley spring. I own, and have built several other rigs which will max out 14 inch travel shocks with leaf springs. No risk of inversion whatsoever. The key is a properly sized (length) and located (shackle hanger location) shackle for the spring...

I can agree with that, my point was more in the context of those that don't want to modify spring hangers and or use custom springs, shackles, etc. I do all this arguing for a SUA setup and I am an avid SOA fan... I think the best ride, flex and value to be had is out of a SOA... :D
 
Here is my truck, the sprigns were well used when I got them

Notice how straight up and down the shackle is?

47b4ce23b3127cce993c156691f500000016109Qcs2TVs38


And then here the truck is at near max flex

47b4ce23b3127cce993c154c91df00000016109Qcs2TVs38
 
Hi All:

I have been running the OME suspension on my '74 FJ40 since 1998. Since I use a soft top or no top, there is little weight in the rear of the truck most of the time.

I run the standard North American market OME13 medium-load front springs, and modified OME14 medium-load rear springs. The OME14s have had one leaf removed, making them a OME140 (Light-load) equivilent. After several years of flexing on the PNW mountain trails I still have lots of arch and plenty of fender rubbing on 33X12.5 BFG MTs.

I have three friends running the CCOT "Hell For Stout" four inch suspension. Two of the guys have 35X12.5 inch tires on their rigs; all three have been happy with the "HFS" springs so far. These springs are longer than stock, which is appropiate for a spring that will have a taller ride height than the stock vehicle suspension.

Regards,

Alan
 
Hi All:

I meant to post a pic; don't know why it did not show.

So, here goes again! :grinpimp:

This is apic from trai lriding last Summer.

Regards,

Alan
HQ11.webp
 
I think "Poser" made it all work for me. There's plenty of room to drill a new hole in the perches and center the wheel. We measured the distance from center hole to each end and there is not enough of a difference to turn the springs around. Cool.... Thanks
 
Last edited:
Please post some pics of before and after new hole is drilled.

I will be doing the same to my ome 40 once the top and tire carrier are installed.

The fact the stock hole is still there and the mod can be reversed fairly easily is more appealing than having to move the hangers.
 
OK here's where I'm at with this spring situation and much happier. I was wrong with my measurements when Honk asked if the distance from the center whole was the same to each end of the spring. It is not!!!! We turned the spring end for end and picked up about an inch or better. We also took
Poser's lead and drilled a whole in the spring perch in case we didn't get enough length. Looks much better and we didn't use the newly drilled whole.
I'll probably have to shim the rear end and at that time remove a leaf or two
and see the difference after breaking them in a bit. Definitely have to have the drive shaft lengthend. A small price to pay to have this behind me. Exhaust system is next and then after nearly six years and my kids college fund, crank her over for the first time. THANX for the help.
 
Last edited:
OK here's where I'm at with this spring situation and much happier. I was wrong with my measurements when Honk asked if the distance from the center whole was the same to each end of the spring. It is not!!!! We turned the spring end for end and picked up about an inch or better. We also took
Poser's lead and drilled a whole in the spring perch in case we didn't get enough length. Looks much better and we didn't use the newly drilled whole.
I'll probably have to shim the rear end and at that time remove a leaf or two
and see the difference after breaking them in a bit. Definitely have to have the drive shaft lengthend. A small price to pay to have this behind me. Exhaust system is next and then after nearly six years and my kids college fund, crank her over for the first time. THANX for the help.
Beautiful!!! I'm PM'ng you!!!
 
I had similar problem with long wheel base 45 and a OME suspension kit I got from Kurt. I put 33s on and when several buddies in the bed rocked it, it almost hit the forward edge. I did a body lift to just the bed of about an inch and have not rubbed a fender yet. Here in Montana we have pot holes a foot deep all over the place and I sure didn't want the tire near the rear of the fender
 
Back
Top Bottom