Oily Intake Manifold

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 10, 2007
Threads
7
Messages
40
Location
Maitland, FL
I need some professional opinions on my intake....

Yesterday I took off the manifold in preparation for replacing the EGR VSV. I've been fighting the P0401 for about 6 years now. When I checked the VSV a few months back, it tested sat. However, the P0401 code returned... Anyhow, I read here that some folks have had the VSV intermittently fail so I thought I would bite the bullet and just replace it.

Back to the manifold. When I removed it, what I found appears to be a thin layer of engine oil on the inside as well as on the flange surface. Should I have an oil film in here??? I understand some oil mist comes in via the PCV. I just didn't expect this.

I do have a K&N filter. The oil is NOT red.
[/ATTACH]
DSC02630 (Medium).webp
DSC02631 (Medium).webp
 
I'm not a professional, but it does look like your intake is sucking in a lot of oil from the PCV system
and has a ton of sludge/oil in the runners.

Clean (soak) that sucker and your throttle body while you got it apart.

I'll let the experts chime in.

Good luck with the P401.

G
 
The K&N did it. I had about a half inch thick layer of oil and dust just in the area inside of the air filter in the filter box.


When I removed the tube from the filter box to the manifold, there was a layer of oil on the manifold.


Get rid of the K&N. I'll ship you my used OEM washable filter for 15 dollars.
 
How much make up oil are you adding per change?

Gee, not sure if I want to get back into the K&N sucks debate again,
but I say no way did that oil come from you K&N.

K&N filters use a very small amount of red oil, not engine oil,
and it is a light machine oil that would not cover the interior of
the intake with black varnish.

This is engine oil probably being sucked into the intake via the PCV system; why so much; don't know: malfunctioning breather-PCV system, worn/stuck oil rings leading to increase blow-by and increase pressure in the crankcase forcing more oil through the PCV system??

We need the experts to chime in.

g
 
Gee, not sure if I want to get back into the K&N sucks debate again,
but I say no way did that oil come from you K&N.
How did you get that I was in any way talking about a K&N in my post? Make up oil is oil added to the crankcase between oil changes.

I was asking because unless it's some crazy amount then I wouldn't even bother and call that normal. I'd imagine anything over 2-3 quarts and you'd be seeing smoke in your exhaust - in which case it's probably leaky rings allowing the crankcase to be pressuized and forcing oil through the PCV system.
 
The oil comes primarily from the PCV valve and secondarily from the K&N (although not all that much unless you oversaturated the thing with oil). I estimate somewhere around 8 tablespoons of oil and crap goes through the PCV every 3K miles. The only way to solve that situation is an effective catch can. There's a FAQ on that if you want to go that route. HTH. :cheers:
 
Was there oil right at the entrance of the manifold where the "air hose plenum" or whatever it's called meets?

If so, it's probably a lot in part due to the K&N. Mine was really bad. I haven't taken anything in my engine apart, but when I wiped the inside of the top part of the manifold off, I got a mess.

I used to have a picture, not sure where it went, but I had to use 3 paper towels, and each one was almost completely black with dust and oil, and that's just wiping as far as I can see into the manifold.


And also, I didn't over-oil the K&N, I got the box, opened it, and then put it into my 80.
 
How did you get that I was in any way talking about a K&N in my post? Make up oil is oil added to the crankcase between oil changes.

I was asking because unless it's some crazy amount then I wouldn't even bother and call that normal. I'd imagine anything over 2-3 quarts and you'd be seeing smoke in your exhaust - in which case it's probably leaky rings allowing the crankcase to be pressuized and forcing oil through the PCV system.

Chibo;
I was commenting on tomatopants post that said it was the K&N as the cause of your problem; I have been using K&N filters for over 20 years; not a problem.

It is from the PCV system. Flush the heck out your engine (internally)
to get out all the old crud, varnish, sludge, etc which may free up your oil rings if the are stuck/dragging; replace the PCV valve, clean out your throttle body and intake as you plan, and consider changing types of oil you use (IMHO).

Then add a catch can; I'm looking for a good one now myself,
I may use the JAZ mini-catch can; it is the only one I could find
(surfing) that has a matt black color; all the rest are some blingy
blue, chrome,etc.

Good luck.
g
 
I just got my Steeda (ala mustang) Catch Can from their website- 69.95 comes with hardware and a good length of hose.

I ran it today for probably around 1hr.........and actually got a few drips of oil which actually amazes me for the first hour alone!

Imagine how much oil these engines are sucking in on a yearly basis.......no wonder theres so much carbon baked onto the tops of pistons- thus increasing compression on these. I have to believe this is the single reason these engines foul in HG- IAC- VSV-TB-EGR and anywhere else in the chain that is touched by this oily gooook.

IM A LITTLE SURPSISED THIS ISNT the single biggest TO DO for anyone purchasing a cruiser.

I have had idle issues for the past 3 months- and on the first day with this Steeda catch can---and a can of REDLINE fuel system cleaner---the idle has already started to correct itself. I imagine a few 100 miles and maybe a can of BG through the intakes--and this will start to fully correct itself.

Imagine what your pistons look like? And when you consider that milling the head a few thousands--will add to compression.....how is a millimeter or two of carbon crud throwing each cylinder out of whack ??---increasing compression to where any HG would blow......much less an already potentially suspect one. Im thinking back to all the pics of HG failures and the caked on carbon on top of the pistons and have to believe that good ol #6 piston is probably pushing 13 or 14:1 while the front pistons are probably at stock 9:1---tell me how the ECM is handling that?

And everyone pinging on high octane gas--has to be compression related. And im betting they are only pinging in good ol #6 or the worst carbon caked pistons of the bunch.
 
Last edited:
Normal, never seen a 1FZ intake without it, it is a nasty mix of oil from the PCV and soot from the EGR.

BTW you could have removed the VSV without removing the upper intake,
 
Normal X2.

DougM
 
Normal, never seen a 1FZ intake without it, it is a nasty mix of oil from the PCV and soot from the EGR.

BTW you could have removed the VSV without removing the upper intake,

Normal X2.

DougM

Normal yes, harmless no! Do something about it and stop worrying with reduced performance from all that crap covering everything from the intake to the exhaust. It is an easy fix for sure. :cheers: :cheers: :cheers:

Link to look at:

https://forum.ih8mud.com/showthread.php?t=87788
 
Raven/Doug/turbo- Thanks for the hand-holding on the oily intake issue. I am seriously considering an oil catch.

chibo - I just recently stopped some oil leaks so I don't have any good data there.

tomatopants - absolutely no oil upstream of the PCV entrance to the intake manifold. Only varnish at the throttle itself. Hose coming off of the air filter was completely dry. Makes me wonder if I'm not oiling my K&N enough...


The intake is back together and all seems well. Now I need to get it out on the interstate to see if I have defeated the P0401 gremlin...
 
Back
Top Bottom