Oil Pump?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 6, 2005
Threads
55
Messages
412
Location
EAST COAST
I am getting no oil pressure at idle and low pressure when I give it some gas. New sending unit, new wires. I ordered an oil pump from CCOT and it should be in today. Is there anything special I might need to know about dropping the oil pan and changing the pump on a 10/74 FJ40 F Motor? I am thinking there is no need to pull the engine for this. Am I right?
My haynes manual is totalled from working in the rain so I am getting no help from it. As always thank you all in advance. :beer:
 
It's the easiest engine oilpan I've ever removed. Some people have found the pan stuck on pretty solidly I guess, but it couldn't be easier to remove.

Get a one piece OEM gasket for it - for sure!

The oil pump is right there - comes down easily too.

But you know that low oil pressure is only a symptom, right?
 
You really need to check the oil pressure with a mechanical gage before you
tear into the engine. It would be good to know the REAL oil pressure in the
following circumstances: cold engine @ IDLE, cold engine at 2500 rpm, hot
engine @ IDLE, hot engine at 2500 rpm. The 2500 is arbitrary. Also, if your
F engine has the remote oil filter, then it has a provision for external adjustment
of the oil bypass pressure. You can get a remote oil pressure gage kit for
$20 or get a shop to do it for you.

It is unlikely that a new oil pump is going to help your problem -- you probably
have some bad bearing wear somewhere. If you do change the pump, you
should check the pressure with the mechanical gage after you change the oil
pump. I would save the old oil (but would strain it) so that you don't get any
"new old effects" on the oil pressure once you install the new pump. Let us
know what the outcome is.
 
Why do you think the oil pressure is low? Did it suddenly change?

Do what the other guys said, but change your filter too. If your filter is plugged and gone into bypass I believe it will show a slight drop in oil pressure (a couple PSI). You really do need some pressure #s though before anyone can give you an answer. Even buy a $20 one like RGENTRY said and just hook it up with out plumbing it to the dash to get some #s.

If you do install the new pump, take out the distributer and turn the pump by hand (after adding oil) with a screw driver to prime the pump and preoil the bearings. If you have the filter mounted on the passenger side, pouring some oil into the passages in the filter base will help too.

***Make sure your distributer is seated all the way and engages the pump when you reinstall it.**** I CAN'T STRESS THIS STATEMENT ENOUGH!

Good luck and let us know the #s. :cheers:
 
Mine sits just below the middle line on the gauge on the highway. Which you would think is low, but it's been running fine this way for years. And this is a truck with 96k on it. I wouldn't trust the stock gauge, put a real one on and find out what the deal is.
 
The stock gauges are notorious liars.

Even if it did have low oil pressure, just putting in a new oil pump isn't likely to change this situation because the low pressure is usually due to excess bearing clearance and not the pump. The engine doesn't need to have high oil pressure as long as everything is getting oiled that needs it.
 
The oil pressure has been low ever since I bought this truck in January. Within the last week The pressure has been getting lower. Now whenever the truck Idles it is registering zero oil pressure. If I give it a little gas the pressure raises to just about halfway as the RPM'S increase.
I have already put on a new painless wiring kit so I know the wires are good, New sending unit. I plan on putting in an after market oil pressure guage and amp meter along with the oil pump. The truck has 300,000 miles on it and runs like a top. I just figured a new pump would be a good idea. One less thing to have to worry about. Plus I will get a peek at the bottom half of my motor.
Thank you all for the replies and advice.
 
I will let you guys what the numbers are when I put the new guage in.
 
It doesn't really matter as long as the rods aren't knocking. I wouldn't fool with it and just run it until it needs work. Then rebuild it and put all new bearings in it and then you can use your new pump. Just looking around and putting a new pump in won't accomplish much. It isn't worth the time and effort.
 
Not true, you can find lots of fun stuff taking the pan off the first time on a new rig. I found globs of permatex in the pan, a small 6mm bolt, and two of the levers broken off of two different fuel pumps. Apparently somebody took 2 pumps to learn the spacer needed to be there. It was a little scary finding that stuff, but it runs great and has good even compression.
 
If I were taking the pan off I might go ahead and plastigage the main bearing
caps (if I were feelng really confident in my ability to get it back together).
I understand the that primary source of low oil pressure is worn main bearings
and worn cam bearings. Can't do much to check the cam bearings.
 
Last edited:
I agree with rgentry. Remember, that the stock gauge is there as a witness only. If you suddenly see a change, I'd check the gauge first making sure that it is grounded and in good condition before tackling some of the more difficult tasks. Remember, look to the obvious first. I know that this can be hard to remember since I've assumed the worst before only to have a problem turn out to be something simple. Try to wire the gauge bypassing the the painless harness that you put in. Make sure that you wire it correctly and don't short it out.

Plastigauge is a goooooood idea and cheap!


Good luck!
 
If your engine doesn't have the external regulator, you should shim the releif valve on the new pump with 1mm or 1.5mm washer as per Mark W's article in the Trails a couple years ago. You could also put in a later style pump (77 and later?) with the Aluminium pickup. You will have to cut one of the baffles in the pan to fit it in though.
 
Back
Top Bottom