Odd Electrical Gremlins? Any Elec Gurus?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 10, 2008
Threads
11
Messages
115
Location
PNW, WA
Hey everyone,
I've been lurking for a while and I searched but didn't quite find what I was looking for, so, here it goes:

I'm "taking care" of a buddy's 1994 FJ80 while he's in Iraq. The biggest issue was that it didn't have working brake lights, other than that it's rock solid. So, I replaced the "STOP" fuse that was burnt out, checked them, no dice, replaced both bulbs, and only the drivers side works. The CHMSL doesn't work either.
Another oddity is that when I depress the brakes the dash lights illuminate, gauges, everything. Oh, and probably the strangest is that when the turn signal clicks back after completing a turn the power door locks trip, either lock or unlock depending on what they were before. Strange.
Would these issues be related? Is there a possible short somewhere, another fuse or relay I need to check out?

I'm quite mechanically inclined, I've already replaced a few things in the engine bay this week, and I've restored and rebuilt a few European cars in the last couple years so don't hesitate to get technical, but please keep in mind I'm not very Japanese car savvy.

Thanks guys.:)


Plans for the FJ80's other mods will be forthcoming. :cool:
 
I'm sorry I don't have a lot of specific information on your situation, other than to offer that an buying the EWD (Electircal Wiring Diagram) book would be a nice "gift" to your buddy for letting you use his rig while he's in Iraq. Might also shed some light on where to look for shorting wires and/or hiccups in the wiring harness. I couldn't imagine trying to solve a problem like this without one.
 
X2 on the EWD. Jap cars are prone to ground loops and issues related with grounding problems (most jap cars switch the ground circuit vs switching the positive). Once you get your EWD, find the page that shows the grounding points. Specifically the ones by the center console, kick panels and under the hood.

After my '94 had ground issues, I removed many of the ground points, scuffed up the paint, retapped the holes and reinstalled the wires. This made a huge difference. Even the power windows went up a little quicker.

Don't overlook the ground wire that attaches to the bottom of the intake runners. It is the main ground for the VSS/speedo, but also causes nasty ground loop issues when it isn't connected after a PO does a shoddy HG job...ask me how I know!
 
Any aftermarket electronics (stereo, alarm, etc)? That would be the first place I'd look. Does the harness look burnt anywhere? I remember something about the harness melting back by the exhaust pipe somewhere.

x2 on the grounding.
 
No aftermarket work on the truck besides a lift kit and tires really.

How can I obtain the EWD? Is it part of the FSH?
Whereabouts on the exhaust should I look for the harness coming into contact? That seems like a rather major flub for a Japanese engineer to make!

I have a week off coming up soon and I'd like to get to the bottom of this, it's like a zen thing for me to fix ish like this. And since you mention the slow windows, thats also something I've noticed, like when I'm rolling up more than one window at a time they go SLOOOOOOOW

Thanks guys, any other info/ideas are greatly appreciated.
 
Okay, I thought it would have something to do with the trailer harness too since it's between the lights. Which "box" do you speak of? Is this where a fuse might be for the trailer harness?
 
Last edited:
Jesus, wow, thanks, I just read every post in that thread and wow that sounds similar.
I'm going to have some time tomorrow afternoon to take out that pesky dangling trailer harness, the one on this LC looks like a aftermarket one, so I'll check both sides but I think I saw the harness on the passenger side when I was inspecting the problem originally.

If anyone has any more input or ideas that would be greatly appreciated.
 
IF you run across anything (red, yellow, blue) that looks like this, only snapped together:

4xoddic-albums-fix-picture2277-3m-tap.jpg


you've found a non-OEM can-o-gremlins often used by shops to eliminate professional results &/or save time. The different colors are for different gauge wires, but Sons-of-Gremlins figure why stock the right one when the wrong one works just as well to birth a Gremlin?

That's a pic of a 3M Scotchlok t-tap in the open position. The little razor blade inside is supposed to only slice thru the wire insulation when the 2 sides are snapped together, & then make connection between the OEM wire & a new wire added to the circuit. HOWEVER, the blade often cuts nearly thru the OEM wire = short waiting to happen + reduced conductivity & > surface area for corrosion.

Here's hoping you don't find any. IF you do, the best route is to remove, 1 by 1, & inspect OEM wire to see IF it is cut nearly in half. IF SO, you'll need to splice the wire to correct. Use real professional tech: splice (twisted wires by adding short length of similar gauge wire, add solder if capable of soldering), electrical tape (better to use heat shrink tubing).

Mr. T doesn't use these at the factory, so any you find were added. Don't mean to :o anyone who uses these; but would suggest there's a better way of outsmarting oneself. :bang:
 
I removed the lower part of the harness, as seen in the pics below. But the problems still persist.
I took some more photos of whats behind the rear cargo passenger side interior panel and the wiring back there. I just want to know if anyone sees anything out of place or something that should be removed?

Here's the removed harness:
CIMG0604.jpg


Where I removed it from:
CIMG0605.jpg


Another connection under the cargo area, not sure if it's aftermarket, it looks OEM and goes up to the front of the truck so I don't know what it's about:
CIMG0606.jpg


Behind the passenger side cargo area panel:
CIMG0600.jpg


This connector is just hanging there and comes up from the bottom of the truck:
CIMG0601.jpg


Closeups of the other connectors:
These go to the taillight:
CIMG0602.jpg

This one I don't know, just looks like it passes through:
CIMG0603.jpg



I hope this helps some
 
In pix 2 you need to plug the 2 that look like they plug together back in, but before you do hit them with some brake cleaner and make sure they are clean and not corroded. As for all the stuff under the side panels they look good and are fine from what I can see .
The trailer harness is aftermarket and not post installed .

HTH some
 
Try the connections under your OEM jack, this one feeds signal, brake and tail lights.
Another point is DS upper hatch: Wires into headliner, LED center brake light and wipers.

Check that ALL brake lights work...

Does the Cruise work? If not, then probably brake wiring, door locks and brake lights again.

You could also try removing the rear bulbs through elimination work your way back to th source of aggrevation by elimination.

I know this because of road salt corrosion.
 
Brodie;

First thing to check on is the battery connections. Then check the black #10 lead from the neg side of the battery lead. It goes to a body ground on the left fender near the battery compartment. This lead carries a lot of the ground current and will corrode at the fender connection point.

Next find other ground points in the engine bay and check them.

Next, is the left rear compartment (tire jack storage) where corroded ground points have caused conditions u mentioned.

Also, under the headliner near the rear stop light (LED). This area ground points have also caused problems.

...

One area many people don't consider is a SHORTED tail light bulb. Not blown open; but shorted. This is rare, but will cause mucho hair pulling trying to figure out why u have the symptoms that are showing up. Some of ur symptoms indicate that a shorted bulb [usually in the rear of the vehicle] is allowing current to feed back into other systems.
 
Alllright thanks, I'll have a chance to check all this out on Friday and let you know how it goes, hopefully I can get it taken care of.
One thing I forgot to mention is that when I removed the aftermarket towing harness the rear turn indicators ceased to work, so I put it back on and they came back, I'd rather have one brake light and turn signals than one brake light and no rear turn indicators.
I got a login to that Toyota tech site with that 24 hour pass and I downloaded just about every PDF file I could get to, and one of them is the grounding point wiring diagram, so hopefully I can use that and get those cleaned up and fix this annoyance.
Again, Thanks to everyone!
 
...but before you do hit them with some brake cleaner and make sure they are clean and not corroded...

May I suggest blowing the dust out with compressed air and then using electrical contact cleaner instead. It's designed just for this purpose. Then get a packet or tube of dielectric grease, available at most auto stores, and put a dollop of it on each connect before you reassemble the connectors. This will help keep moisture from corroding the contacts. Brake cleaner will work in a pinch, but contact cleaner is better because it leaves a film that displaces moisture and contains a lubricant.

And since you've got the trailer light adapter disconnected anyway, plug the two OEM connectors that mate with one another back together and see how things work with the adapter out of the circuit. If your symptoms change then the trailer adapter may be faulty.

As to the original question, nothing looks suspicious in your photos.
 
With the trailer adapter disconnected and the stop lamp bulbs removed from their sockets, do the dash lights still come on when you step on the brakes? In the jack storage area there's a connector that ties in the brake light circuit to the back door stop LED. If you disconnect this too, then do the dash lights come on? The brake light circuit is about is about as simple as it gets, so that's a good one to focus your troubleshooting on.

Other general thoughts: 1) there may be more than one problem you're chasing; 2) what's the general condition of the truck? Your pics show a pretty clean underside so I'm guessing it's not from a place that uses salt on roads in the winter and hence there's not much corrosion to worry about, but please confirm this.

Oh, and what's a CHMSL?
EDIT - Answer: Center High-Mount Stop Light (on tailgate door).
 
Last edited:
You're not going to believe this one....

First off, thank you all, each and every comment helped me out in troubleshooting the whole problem.

So, I started with cleaning all the ground contact points, didn't fix the problem, but, it lead me to an old alarm system wired in under the dash.
I removed the old inactive alarm, re-spliced and soldered all the wires that were tapped using a razor in line tap as mentioned by 4xottic.
This didn't solve the light problem, but, the locking/unlocking of doors did stop, good start.

I then started to check the whole wiring harness in the back end of the truck, everything behind the front seats was pulled out and I got into the door panels and under the carpet to check everything.
It all looked good and I re-spliced and soldered all the connections from the door lock control wires that were tapped from the old alarm.

While I was checking all the lights again I noticed that the W5W size bulb that's in the rear red drivers side sidemarker was out. I removed it and noticed that the glass inside was all glazed over and basically looked like it was filled with white paint. I figured this was bad, obvoiously, so I replaced it.

BINGO!

There must have been a short in this bulb that was somehow causing a problem for the back end. Once I replaced all the bulbs again in the tail lights while I was preparing to clean up for the night I turned the lights back on to see if the W5W bulb was working now and I noticed that both tail lights were now working. I then put one of my tool bags on my brake pedal and Ta-fxxxing-da they worked!



So now I can move on to the next part of my plan. Respraying the whole truck. Plan is to spray it in flat, or lusterless, Olive Drab green, along with the wheels, and to black rhino-line (or something similar) the fender flares, side steps, lower doors and bumpers. So if anyone has any tips for this or know of any good threads to forward onto me please do.

Again, THANK YOU to everyone that replied. Every single thing helped in the end, what an amazing community!
 
The brake lights are on a different fused circuit from the tail/marker lights, so I really don't see how the bad marker light could of been making the brake lights non-functional. That part just doesn't make sense.
 
Back
Top Bottom