nv4500 & 2F

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 9, 2005
Threads
271
Messages
5,828
Location
Cary, NC
Anyone running this w/ the stock 4spd txfer case? I've seen people say this is too long of a drivetrain. Opinions? My current setup is:
STOCK:
2F Engine - Not going to change!
4spd stock transmission - 3rd gear synchro going bad
4spd stock transfer case - less than 500mi since rebuild - would like to retain

What I am looking for:
My top priority is crawl ratio, although I don't need anything crazy - would like to have it somewhere around 50:1+

Driveability - I want to be able to drive this thing to take it wheeling....I don't have a trailer :(

Budget - Cost to do this swap is a very big consideration. I would give up the 5spd option to save $500 or more.

Thanks for any input, and if there is anyone in the Raleigh area who loves wrenching on FJ40's let me know :)
 
SM420
Cheap, lots of info, great gearing, and a good match to the 2F.
I have 56:1 crawl ratio with the SM420, and stock 4 speed t-case.
I am in the whole conversion less than $700 and that's with a NEW SM420.

I drive my Cruiser every single day and I have had no problems with drivabliity.

I feel that the NV4500 isn't well suited to the powerband fo the 2F. IT was designed to be put behind a diesel or a v8.
I'd say run an SM420 if you want cheap gearing, or if you want a 5 speed, buck up to an H55.
 
Last edited:
That's how I leaning James. Here's what I figure cost-wise

AA Kit 50-2602 $520
AA Kit 712520 $190
SM420 $??? - still sourcing
3spd Bellhousing $??? - still sourcing

What other costs am I missing? Clutch - can I retain stock clutch?

Thanks,
Michael Weller
 
mtweller said:
That's how I leaning James. Here's what I figure cost-wise

AA Kit 50-2602 $520
AA Kit 712520 $190
SM420 $??? - still sourcing
3spd Bellhousing $??? - still sourcing

What other costs am I missing? Clutch - can I retain stock clutch?

Thanks,
Michael Weller

You can get the plate adapter from Extreme Bends for less money than the AA kit.

http://www.extremebends.com/sm420/sm420-cat.shtml

I'd go that route, as you don't usually have to modify drivelines to use the plate adapter (if going from a stock 4 speed toyota tranny). I'd get the adapter, the input gear and the Bellhousign 'kit' from them.

You will also need a 3 speed output flange for the t-case and a 3 speed style driveshaft to clearance the side of the tranny. I'd get those parts, and the 3 speed bellhousing, from our very own CruiserOutfit

For a transmission, give Antelope Valley Equipement a call (661) 945-6788. They have new old stock SM420's. Their price has gone up a little since I got mine, but I feel that the tranny is a bargain at twice the price I paid.

As far as the clutch goes, you have a few options.

The cheapest and easiest thing to do is get a 10.4" Chevy clutch from your favorite auto parts store (source a 1967 chevy truck with an inline 6) and bolt it up behind the stock Pressure plate. The chevy tranny will stab right into it.
 
I got my SM420 adapter plate from Mike Smythe for $100. Woody had my plate to copy it to start selling again. I don't know if he is yet.


I would let cost of adapters make my decision about SM420 vs SM465. Woody's SM465 adapter is a deal.

I am also using one of the NOS SM420s from Antelope Valley. It is sweet. However, you must source a civilian top plate for it, as they come with some sort of funky remote linkage top plate. Toyota 3sp shifters work fine.
 
CruisinGA said:
I got my SM420 adapter plate from Mike Smythe for $100. Woody had my plate to copy it to start selling again. I don't know if he is yet.


I would let cost of adapters make my decision about SM420 vs SM465. Woody's SM465 adapter is a deal.

I am also using one of the NOS SM420s from Antelope Valley. It is sweet. However, you must source a civilian top plate for it, as they come with some sort of funky remote linkage top plate. Toyota 3sp shifters work fine.


Unfortunatly, Mike and Woody are no longer making adapters.

Here is a top cover fo an SM420

http://cgi.ebay.com/ebaymotors/1964...ryZ34208QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

You can mod your 4 speed shifter by adding 3/4" of bar stock to the shifter and it works and looks sWEET
 
Hi All:

Your easiest solution would be to replace your H42 transmission with a H41 four speed.

The SM420 swap will net lower gears, but will effectively be a three speed transmission on the street. Same with a SM465 swap.

How low a gearing you need really depends on what type of 'wheeling you are doing.

Good luck!

Alan
 
Josie'sLandCruiser said:
The SM420 swap will net lower gears, but will effectively be a three speed transmission on the street. Same with a SM465 swap.

Alan


Josie is definatly right about the 3 spd for street thing, however, I will add that I DD my 40 with an 420, worn out F, and 38's and it really works fine. I'm honestly amazed at how well it drives considering the engine, tire size, and large gaps between gears. I let a lot of different people drive the truck on a regular basis and no one has had any problem.
 
Back
Top Bottom