Now the fun begins

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 17, 2015
Threads
60
Messages
1,094
Location
Yuma, Az
im starting this thread because im now the proud owner of a 96 fzj80. this thread will show the slow transformation (as fast as those 20% VA checks come in) of my new toy into a expedition vehicle. i have lots of questions and i will use the search feature as much as i can but sometimes it doesnt answer specific questions. there will also be lots of pics.
it has 190k miles and is in stock configuration with lockers.
now my overall plan is arb bumper, slee sliders and rear bumper, 3"ome lift, either 33s or 35s; havnt decided yet. gobi roof rack, cb of course and lights as well as a winch and an arb diff vent. i have the chicom snorkel but need to install it when the wife isnt there. i dont want her seeing me drill into the body!
when i picked it up the green paint on the hood, fender flares and roof is faded as usual. the sunvisors probably need replaced as does the front leather. (grey) didnt come with the back seats, the lockers were hard to get to lock in but with some turning and exersize they did. the engine runs well but wont win any drag races. doesnt smoke but smells like fuel when warming up and smells a bit like burning oil when i get home from a drive and shut it down.
this saturday im taking it in for a multi point inspection for free. this dealership is good to go here in yuma.
ill be flushing all the fluids out and replacing all the filters and keeping a detailed log of everything done.
 
A few pics

IMG_20150518_185732_915.webp


IMG_20150516_200736_896.webp


IMG_20150516_201537_752.webp
 
Welcome! The fuel smell might be a charcoal canister issue. Mine (which I haven't driven yet due to blown headgasket) smells like gas just sitting there on a warm day. Burning oil smell is probably oil leaking down on the exhaust.
 
hopefully thats all it is. i cant see any oil leaks but ill find it eventually. i drove it over 200 miles so far and i havnt had to add any oil so thats good. as a matter of fact, the level hasnt moved on the dipstick at all. i added a half of a can of seafoam to break any gunk loose and the oil is still the same color a week later. the temp gauge stays in the middle in the arizona heat with ac on full blast but the oil pressure gauge drops out when it heats up. im going to go to 10-40 just because the heat here so that may help...
tomorrow im adding a can of seafoam to the diffs. 1/2 front and 1/2 rear then putt around the desert. still need to change the seat gears and add the cdl button as well as the 7 pin mod unless its not needed ((7 pin mod). which one of the knockouts is the cdl button supposed to go on for the 96?
 
Check the four bolts on the bottom of both front knuckles to make ure they are tight. They have a tendency to work loose and are not noticeable until it's too late and it's a catastrophic failure.

Welcome to the addiction! :flipoff2::flipoff2::flipoff2:
 
You can put the CDL switch in any accessible blank spot above the climate control switches. Fifteen minute mod, use any Toyota hazard switch from that era. I got one at a junk yard for ten bucks.
 
Check the four bolts on the bottom of both front knuckles to make ure they are tight. They have a tendency to work loose and are not noticeable until it's too late and it's a catastrophic failure.

Welcome to the addiction! :flipoff2::flipoff2::flipoff2:
which 4 bolts? pic please. still learning. if it was a yj i would know but im new to the 80 series...
 
The four bolts that hold the steering arm to the bottom of the knuckles. You can only see the two outer bolts at the bottom of the knuckle here. Steering arm is sticking out to the right of the pic (rear of the truck...this is the DS). Second picture is from the bottom before I disassembled it. Your tie rod attaches to the arm on the bottom of both knuckles.
IMG_20141101_193412670.webp


IMG_20141025_244102028.webp


Mine worked loose after about 3000 miles of driving after I bought it. As I found out later, my PO had hit a guardrail with the RF corner and sheared off one of the studs, two others worked loose and fell out, and the fourth was almost out of its hole when I discovered it when washing the truck in a manual car-wash. My brain picked up something wasn't right, but it took a day for me to wake up in the morning and say"Wait a minute! I saw something under there that wasn't right!". When I went and checked (at work) the last one was less than finger tight and had almost fallen out. I snugged it up and drove very gently home and parked it until I could properly fix it.

When I rebuilt my front axle, I remove and replaced ALL the studs, locked them in with Loctite red, and then torqued the nuts on with Loctite blue.

Let me know if this is not clear enough.
 
I notice your black '96 has chrome emblems. My black '96 has gold emblems. Anyone know why they did them two ways?View attachment 1080219

Read in the middle. I typed out a bunch before I re-read your post. Bear with my ramblings...

The 96's (and only 96) had a special version with "The Chrome Package" I have one. The chrome package included chrome door handles, chrome gutter trim, chrome mirrors, and in my case, chrome plated factory rims and a chrome brush guard. My emblems on the front grille and the rear tailgate were gold plated and I have a certificate in the glove box of certified 24K gold plating on these emblems. The chrome wheels and brush guard were dealer or port-installed options. The gold emblems were typically dealer installed options.

As you may know, chrome parts are the "red-headed step-child" of parts on here. Everyone tells you that chrome is for bathroom fixtures, not trucks. I personally LIKE the chrome.

My chrome wheels are peeling BAD. I cannot re-chrome them, as they are WAAAY too pitted for the chromer to warrant them. I cannot just blast them to clean them up because the chrome is much harder than the aluminum and the AL will remove faster than the CR. I need new wheels when I get the chance and when I do, I will polish the AL to make them LOOK chrome (like big trucks do).
 
The four bolts that hold the steering arm to the bottom of the knuckles. You can only see the two outer bolts at the bottom of the knuckle here. Steering arm is sticking out to the right of the pic (rear of the truck...this is the DS). Second picture is from the bottom before I disassembled it. Your tie rod attaches to the arm on the bottom of both knuckles. View attachment 1080210

View attachment 1080216

Mine worked loose after about 3000 miles of driving after I bought it. As I found out later, my PO had hit a guardrail with the RF corner and sheared off one of the studs, two others worked loose and fell out, and the fourth was almost out of its hole when I discovered it when washing the truck in a manual car-wash. My brain picked up something wasn't right, but it took a day for me to wake up in the morning and say"Wait a minute! I saw something under there that wasn't right!". When I went and checked (at work) the last one was less than finger tight and had almost fallen out. I snugged it up and drove very gently home and parked it until I could properly fix it.

When I rebuilt my front axle, I remove and replaced ALL the studs, locked them in with Loctite red, and then torqued the nuts on with Loctite blue.

Let me know if this is not clear enough.
Got it. Soon as I seen the pics. I'll check them this weekend. Thanks. Anything else I should look for?
 
The way I look at it, I fix stuff that is absolutely necessary first. In my case, it was strip the tint off the front windows, and fix the mirrors and the wiper motor.

Then it's:
1) Make it stop
2) Make it safe
3) Make it go
4) Add the cool $hit.
5) Have fun!
6) Research Step 6 to see what that's about! There's ALWAYS a Step 6.
 
The way I look at it, I fix stuff that is absolutely necessary first. In my case, it was strip the tint off the front windows, and fix the mirrors and the wiper motor.

Then it's:
1) Make it stop
2) Make it safe
3) Make it go
4) Add the cool $hit.
5) Have fun!
6) Research Step 6 to see what that's about! There's ALWAYS a Step 6.
Everything is good safety wise, it will need new tires soon tho...
 
Back
Top Bottom