Noise when turning.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 10, 2006
Threads
144
Messages
1,029
Location
Minnesota
So,
I've got a clicking noise when making u-turns or backing out the driveway, or sharp turns. I thought that doing a front axle rebuild may fix the noise, but the noise is still there. Could my birfs be bad? I cleaned out everything very well when I did my front axle rebuild. When going straight, everything seems normal.
Does this sound like something dangerous to keep driving as is? Wether I engage my CDL or not, it doesn't make any difference at all.
Any ideas?
-lispeej
 
I sounds like Birfields, Can you tell if it is isolated to one side or the other? The only other thing it might be is a bad spindle.
 
my 93 got clicking noise before this happen,ps side
birfields1.webp
birfields2.webp
birfields3.webp
 
my 93 got clicking noise before this happen,ps side

Yikes!! THat looks scary. My spindles look ok. I might just run it as is until next summer then I'll think about replacing the birfs.
Whether i turn left or right, it makes no difference. But when going straight. It's all good.
 
As others have stated, it sounds like BBS (broken birf syndrome) to me. Did you swap sides with the birfs when you did your rebuild? I swapped mine even though they weren't clicking because I saw they had some wear marks. If you don't disassemble the the cage when you do the rebuild it is tough to see some of the wear.

I personally wouldn't drive it until you figure out what it is because it could make the repairs even more expensive.
 
As others have stated, it sounds like BBS (broken birf syndrome) to me. Did you swap sides with the birfs when you did your rebuild? I swapped mine even though they weren't clicking because I saw they had some wear marks. If you don't disassemble the the cage when you do the rebuild it is tough to see some of the wear.

I personally wouldn't drive it until you figure out what it is because it could make the repairs even more expensive.

x2 :cheers:
 
I'll probably redo the front axle rebuild and install new birfs.
I really hope this will fix the issue. I'd like to drive this thing during winter. FUN STUFF......
 
Yikes!! THat looks scary. My spindles look ok. I might just run it as is until next summer then I'll think about replacing the birfs.
Whether i turn left or right, it makes no difference. But when going straight. It's all good.

happening on hi-way doing 75mi=h
 
(Caution Ahead - Minor Hijack In Progress)

I think my Birfs are on their last leg as well. What's the best replacement...OEM or Longfields (chromoly)? I won't be doing any serious wheelin.
 
When you had the birfs apart, did they have wear dimples in the star or bell? Did you swap them side to side? The greatest wear point is close to center of the ball movement, on the forward drive side of the grooves. This is a small dimple, divot, when the steering is turned the balls move at full travel and are forced across the dimple causing the click.

Worn birfs will click and their strength is compromised, but probably aren't going to fail in normal driving, unless really bad. Once they are clicking they wear faster, so need to be replaced relatively soon and I wouldn't trust them for trail use. Greasing clickers usually isn't going to do any good, swapping side to side may somewhat extend street life, but even if they no longer click their strength is still compromised.
 
I'm researching on what I need for new birfs. So far, if I go with the 27 spline chromoly birfs, I will have to get new drive flanges, is this correct? If I can find a set of 91-92, everything should be direct fit.
Does anyone make good quality aftermarkets for 91-92? What are prices: dealer vs. aftermarket.??
 
OEM comes complete/fully assembled? Any ideas on pricing?

The birfield is an assembly consisting of 9 parts. A bell (aka tulip), the star, the cage, and 6 large ball bearings. A factory birf for an ABS truck will also have an ABS ring. These 9-10 parts come in one assembly from Toyota.

Does that answer your question?

Call Cruiserdan for pricing. Expect to hear something around $500 for a new Toyota birfield for your truck.

-B-
 
Last edited:
Your rig has the early type birf, so will need new longer type drive plates to go with the new birfs. Some have run generic birfs, wouldn't expect OEM life, from e-bay and CV unlimited.
 
Back
Top Bottom