No part number on starter

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 21, 2003
Threads
78
Messages
585
My starter has been hesitating so I figured I would replace the contacts. Easy enough. So after searching, I found that there were two different starters on our fzj's. I looked for the part number label on the starter of my 97, but there were no markings or labels of any kind. Can I assume that my starter is an aftermarket unit and that I won't be replacing the contacts? It's been a bumper few weeks. My powersteering pump is dying, moaning and whining. The cheapskate in me wants to buy the $159 lifetime warranty powersteering pump at Autozone, but the responsible side of me should go to toyota.
 
Go OEM

A little advice from someone who just replaced his power steering pump. It can be a royal PITA. It's not something you want to do over and over again which is what you'll be doing if you go the autozone route. Cough of the dough, give CDan a call and do it right. My OEM P/S pump lasted 170,000 and probably could have made it to 200,000. I don't think you'll get anywhere near the life out of an aftermarket unit. Just my 2 cents. :D


PAB
 
Thanks for the link to the starter thread. I've got my old 93 in the driveway that I'm on the fence whether tosell whole or part out(275k miles). I'll know the starter on it was having issues before I parked it last month, but it might be an oem 2.2 unit. I'll check it out tonight after work. I planned on ordering the oem power steering pump today. Thanks for the help.
 
Just fixed my starter hesitation and it may or may not be your problem. I thought it was the contacts and when I opened up the solenoid they didnt look to bad but I put them on a wire wheel and polished them up. I pretty much knew that wasnt the problem so I pulled the motor apart and sure enough one of my brushess was rusted inplace and not making contact. in a hurry I just worked it in and out with some wd40 and got it loose, the Armature and the brushes looked swell with a truck with 186k. Anyways put it together and man it spinned it like a top, been a long time since it did that. This all came from a river crossing years ago.
 
I changed my starter a couple of months ago. The one that was on the truck (PO) was a parts store special and is now somewhere in a land fill.

I put in a 2.0 Toyota reman starter that I got from cruiserdan. It is literally twice the size of the parts store special that I threw out.

Give American Toyota a call and talk to Dan. He has always gotten me the right part quickly.
 
I ordered the powersteering pump from our Menlove here in Utah as they support Wasatch Cruisers. I pulled the part number off the starter on my old 93, but must have read it wrong because it didn't match either style. I'll look again after I get the kids to bed tonight.

John, Thanks for the advice on diggin a little deeper into the starter. Before the 93 started having problems it would immediately turn over as soon as you turned the key. Our new 97 takes its sweet old time to even start spinning the starter. Is this a common delay? Maybe a full second and a half or two seconds. I know, Picky Picky but count to two. Thats before the starter even starts to spin. Its just wierd.
 
Just a little more info on my problem. Mine was intermittent but always when it was cold or the first start of the day. When you turned the key you could see the voltmeter dip if the center hash mark is 9 volts it would go to 7 volts I found that it would ususally adventually start. The reason I dug into mine is that I bought a supposedly the correct rebuilt and after getting my old one out found the motor was about 3/4 inch shorter than the stock being its a pain to get the starter out and paying what I felt was too much for something that wasnt the same led me to dig into mine. The bottom line is now when I crank my volts only dip to above the center hash mark a huge difference. Right or wrong I pumped some grease into my gear reduction housing and pumped some grease into the bearing that goes into housing off the armature. the one on the brush end was sealed and felt good.
 
Thanks John. I went out this morning (5 degrees out there) and looked at the numbers on the starter again. I'm pretty sure it is a 2.0 starter and must have been replaced at some point by the PO. I still think the number on my starter ends with 40 instead of the 2.2 ending in 50 and the 2.0 ending in 60. I will have to man up and go out tonight to remove it to make sure. The case has the external bolts like the 2.0 Thanks again for the help.
 
Back
Top Bottom