Newbie's Project Baseline 3FE 2008

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 13, 2007
Threads
108
Messages
479
Location
Arizona
I about 9 months ago I bought my first LC. I found the site a few months ago and have learned a great deal since then. I knew nothing of automoitive prior buying my cruiser. I vowed to dedicate myself to learn about how to care for this girl, instead of taking her to the shop and hoping the guys weren't hosing me.

The mods on the truck were there when I bought it. Though I think it was mantained relatively well, I have no solid proof. My goal is to baseline out the truck over the next few months and maybe get to some mods. I know most of this stuff you guys do in a weekend if not a day. But this is all a learning process for me.

Here is what I have done so far:

Oil change the first week with Lucas added
Rear Diff Gasket exchage to stop leak first week. (Done at shop)
New bypass hose when sprang a leak. Did that one myself.
New raditor and coolant after plastic Radiator cracked.
New belts at time of radiator repalcement.
Front diff drain and fill. (yesterday, Took forever but did it myself) Plan to redrain again to get out the rest of the sludge.

Future PM Planned:
Tranny flush
Trasnfer case flush
Mutliple oil changes ended with synthetic oil in motor
New Plugs
New Distubutor and wires
Timing adjustement
KN air filter
Fuel Filter
O2 sensors
Lube Chassis

Is there anything I'm missing?


Thanks to all who have answered many questions over the last few weeks and offered suggestions. At time I feel like a child with a 1000 questions to ask. Thanks again!!
 
If you are looking for things to check out, pull down the drive lines and clean all the crud in the slip yokes and fill with some new grease.
sounds like a good list, But I would just use the oem paper filters, I have had bad experience with k&n style filters as if you do not get the oil on correctly it will dirty quickly. Oh and clean out the tuna can on the bottom of the air intake.
Dave
 
Got it, will add it to list. THANKS!
 
x2 on forget the K&N. I had one in for a while.... till I read up on them. You should look into that Lucas treatment (if it is the stuff I am thinking off, there is a video on bobistheoilguy.com showing how it leads to foaming of the oil... not good). Edit-found it: What about Additives?

Should at least top off the moly grease in your knuckles, more if they are leaking. Check the breathers (axles, transfer if you can find/reach it) to make sure they are working properly.
How about a fuel system flush prior to the fuel filter, throttle-body and intake chamber clean.
Check the slack in your throttle and tranny cables.
Check the operation of your PCV valve.
......
 
Last edited:
KN air filter

No x3

I have had bad experiences as well. When I replaced my K&N, I had a nice thick layer of goop/oil/whateveryouwannacallit throughout the entire intake tube. I never oiled it, as it came pre-oiled. Yet dust/oil still got through.

[/rant]
 
How do I flush the fuel system and claen the throttle body and intake chamber?
 
Go to NAPA and buy a can of BG44K, pour it in the gas tank with 10-15 gallons of gas. It will cost about $15 for one little can, but does a good job. Then buy some Berryman's spray carb/throttle body cleaner, pull the PCV hose off the throttle body and spray the entire can in that one port with the engine running. Someone will have to keep the engine running while you do that. If you buy two cans, you can spray that into all the other throttle body and intake ports; any port that sucks air while the engine is running will pull the cleaner into the intake.

Regarding the K&N filters; there are some (as above) that don't like them. I have been using them for over 20 years; not one problem. I also have not bought a paper filter for over 15 years. Most of the oil that people see in their intake manifolds and on the butterfly valve is from the PCV system sucking oil from the inside the valve cover and from the EGR system, IMO.

You also want to carefully remove the air intake assembly, the big black rubber hose that runs from the air filter container to the throttle body. And then clean the butterfly valve. I believe this in covered in the FAQ's. Check the air hose for cracks; very common.

Ditto on the Lucas; better to just use good oil. No need to flush the transfer case unless someone put the wrong fluid in there; IME they stay very clean; just drain and refill, same with the rear diff.

Lots of opinions on the tranny service; many say drop the pan, some say no need.
Either way, to completely change out the fluid, you need to find a shop that uses the type of machine that does not force the new fluid through. Use at least 16-18 quarts of new fluid. I have used LUBEGARDs tranny flush product before a flush; did a good job.
 
Last edited:
How do I flush the fuel system and claen the throttle body and intake chamber?

BG44K is said to be the best fuel system treatment, I've used Sea Foam.... Just run through the tank (I usually like to run it strong, so either half a tank of gas, or double the regular dose to accommodate the 90L tank).

Get a can of throttle body cleaner and follow the directions, you will remove the air hose at the throttle body and spray around inside, to loosen/remove all the carbon gum crap in around the throttle plate and down stream.

Unfortunately with the 3FE you can't run the engine with the air hose detached (bypasses the air meter) while you spray........ Might want to feed some cleaner through the major vacuum hoses around the throttle body while it is running though. Some of us have run Sea Foam through a major vacuum hose in this way to de-gunk the intake chamber and de-carbon the combustion chambers. Others question if this actually does anything positive (I believe it does). The EGR system pumps a lot of crap back into the intake, so I would think cleaning it out can only be a good thing. I have also noticed long highway drives do it a lot of good.

Other possibilities for de-carboning include misting water into the intake, or an Italian tune-up - running the truck hard on the throttle out on the highway for 1/2 hour or so. Others may have differing opinions.

When I started working on my truck, the big improvements came with a new cap and rotor, and the fuel filter. As others have said, the 3FE is sensitive to air filter performance as well.

Hope this helps,
Curt.
 
Hey guys like I said. I can't thank you enough for all your help. My wife is starting to hate my baby. Much like she is jealous of my Dog and Mt Bike. She says, "Its just a stupid 15 year old truck!" And can't understand why I dont want her driving it.
 
Can anyone offer any help on lubbing the chassis and undercarriage, ball joints etc....
 
Back
Top Bottom