newbie

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 13, 2007
Threads
2
Messages
3
Location
Northern Kentucky (Greater Cincinnati)
I recently bought a 1991 Land Cruiser with 145k, mint body, but a few minor suspension/transmission problems.

1st Q: I've looked high and low but have not been able to find an aftermarket cold air intake that will fit my 91. If there is such a fit, does anyone know where? I'm attempting to increase the MPG from a low 12 to somewhere around 17. Other modifications/repairs that would get me closer to the 17mpg mark would also be desireable.

2nd Q: I think there might be a transmission problem. It doesn't slip gears, but there is a loud thud when I shift from D to R or just from P to D, or R (really any gear for that matter). Does this sound like a transmission problem?

3rd Q: Suspension parts. I know I need shocks for the bouncing all over the highway that I'm doing, but I also want to make sure I have all my suspension problems solved before winter hits. What's typical to change around the 145k mile mark?

Sorry about all the Qs. I'm new to this forum and really appreciate any answers I recieve!
 
Question 1: Ive never heard of one available but Ive also never heard of a MPG improvement with one either

Question 2: Probably your U-Joints check your driveshafts.

Questions 3: Are you looking to lift it? If not, check out www.sleeoffroad.com for their stock height replacement kit or call cruiserdan and get new toyota OEM shocks and coils.
 
We manufacture air cleaner assemblies, but not for the FJ80. If we did, they would not get you from 12 mpg to 15 mpg, let alone 17 mpg.

Can't help with your tranny problem. Don't, and haven't owned an FJ with auto tranny. We've always heard those trannys were troublesome, so never even made a V8 kit for them. All FJ80 auto tranny lovers please don't jump on my bones on this, I offer no proof, nor do I care!!!!

Regarding suspension, I become more and more partial every day to the Downey suspension kit we make as I find more and more people who agree with me that ******brands are too firm and too butt high.
 
There is at least one "cold air"/ high flow kit out there for the 3FE. But I would not go that route myself. It will let increased levels of dust in along with any increased air flow. It is also MUCH MUCH less resistant to water intrusion than the stock setup. The factory air cleaner actually does pretty good on the "cool air" front. It draws from under the front fender and I doubt that you will see any improvement with an aftermarket air cleaner assembly. It also has a very large filter element and offers minimal restriction.

Changing it out won't gain you any noticeable power or fuel mileage benefits either.


The A440F has gotten a lot of raps in the FJ62s. But most people forget that the trannys that have been reported as giving problems are extremely high mileage units that have been hard used. This tranny has performed yeoman service in a variety of other rigs, including the FJ80s (and lots of the '62s as well). It is a very stout unit.

I have owned and used and worked on these trannys.

Downey may not, but Advance Adapters does make the adapters needed to put V8s in front of this tranny and it has been done with success.


I have not heard of anyone using the Downey suspension, so I won't comment on it. But I have heard of no one who has been disappointed with the OME suspension kits or components for the '80 series. I have my own dissatisfaction with some of their leaf spring systems under some of the other models, but no one I know who has used their stuff under the '80s has had any complaints either for road use or on the trails.
But your question wasn't about swapping in a lift kit, but rather what you need to address for PM purposes. The quick answer is probably... nothing. ;)

Check and likely replace your shocks. Check the bushings in the suspension system for wear or degeneration. Make sure that your wheel bearings and knuckle bearings are not loose/sloppy. Check your tie rod ends too. Chances are that will cover it for you.


The thunk in your drivetrain is the result of cumulative backlash in the entire system. With a full time 4x4 system like this every bit of play in the entire system, from front to back contributes to the clunk when loading the system first one way and then the other.
One weakness in the tranny/Tcase setup in your rig is that the engagement of the inner splines on the T/C input gear and the tranny output shaft is very short. This increases the loading on these surfaces and in many cases they wear badly. These worn splines make for a lot of slop and this causes a very noticeable clunk like what you are experiencing.

There is a company in Oz (McNamera) that makes a replacement gear for this application It also replaces the PTO spacer which rids behind the input gear and uses this area of splines on the output shaft to carry the load that the original section no longer can handle. This is a very effective solution to this problem and relatively inexpensive. Especially when compared to replacing the output shaft of the tranny.

If you prefer to do the work yourself you could use another, unworn, gear with the same splineing, machine the outer portion off and and weld the inner section to the existing input gear to replace the PTO spacer in the same manner.

But before you run off in this direction, check all your ujoints and pinion flanges/bearings for slack. Remember, it all adds up so if you have a little slack here and a little slack here, you wind up with a lot of slack when you shift it into gear.


Mark...
 
...Other modifications/repairs that would get me closer to the 17mpg mark would also be desireable.



thumb_Steep_Grade.jpg
 
thanks

Thanks for all the replies! I've got some audio issues I still want to tackle as well. Anyone know if 6 1/2s will fit in the front or side doors with some modifications?

As far as the suspension is concerned should I go ahead and replace all four shocks and springs at the same time or can I do front/rear pair at a time? Also, what's a good method for checking the bushings/shocks/springs to determine what needs immediate replacement?

I've been doing loads of reading, as many have said I'll do, but I still haven't found a "around 150k mi" maintainence schedule. I've only invested $5000 in my baby but I'd like to keep her around for many years to come!

Again, thanks for all the support!
 
1) The A440F tranny does very well in 91-92 Cruisers due to the stock auxiliary tranny cooler, which the FJ62 lacks.

2) You really should search this section with the keyword "clunk". Otherwise you'll only see a couple folks' advice, some whom own FJ80's (91-92) and understand this issue on our rigs, and some who don't. There's just no other way to get the whole picture.

Welcome,

Curtis
91FJ80, 239k
 
Welcome

Welcome...:flipoff2: Doesn't take long for the addiction to set in does it?? :D
 
FAQ is your friend, lots of info there.

I have a '92 that I paid $5500 for. It had new A/C system, new alt, tires, starter, and some work done on the t-case rear out-put. New radiator too.

I rebuilt the front, and rear axles. Added some 4:88 gears, don't waist your money on 4:56's (they come with 4:10's stock). I replaced both BIRFs with new Toyota units, also new drive-flanges (these usually are the major culprit in the "Clunk". I replaced my shocks with some Monroe's, which make the OME shocks. The Monroe shocks are too soft in my opinion, and will cost about the same as a whole lift kit from slee if you have the shocks put on at a shop. I've also added 15x10 inch MT classic rims with some new BFG AT KO's in a 33x12.50. Really rides well with the 4:88's.

Most of us with the early 80's will tell you that the "clunk" is a normal aspect of these earlier year 80's.

As for the intake, you wouldn't gain much from a cold air in mileage. I think you'll notice the biggest improvement in fuel mileage with a gear swap to 4:88's with tire from stock size to 33's.

I also adj. the tranny kick-down and throttle cables fro smoother shifting. This will also help with the clunk. My timing is advanced, and I run high test petrol, but seems to really run much better that way. You'll just have to get the tranny dialed in with the kick-down to improve the ride and drive ability. You also can manually shift the tranny for quicker take off, and interstate merging.

Welcome, and LOVE all the new 3FE's around here.
 
Back
Top Bottom