Newbie Master Cylinder Question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 1, 2008
Threads
10
Messages
45
Location
Red Lodge, MT
I just bought a '96 LX450 with 95k miles. My wrenching experience is limited to oil changes and brake pads, but I'm looking forward to learning on the 80. I just found the number for Toyota Publications, and the FSM is on the way. However, I have a brake problem and the truck is currently in at a dealer. I took it in because the brakes were spongy and if I pushed them very slowly (on a downhill and over 15 seconds or so) I could push the brake pedal nearly to the floor and barely slowing the car. Stepping on the brake harder and quicker it stopped fine but was a bit spongy.

They determined the MC is bad and needs replacing, and want about $450 to do it, parts and labor. I called Cruiser Dan today and can get a MC for about $160. Do I need other parts for this job? And is it one to tackle myself? Being it is the brakes I figure I'll need to get it right the first time. I have a buddy that has replaced brake fluid on other vehicles that could help. I have been searching for 45 minutes and haven't found a thread on replacing this. Thanks for the help.
 
Its actually really simple to do. Just bench bleed the master before you install it. Then do the install which is cake itself. Then its very very helpful to have a buddy pump the brakes while you bleed it. You can use the one man one but its not as handy as having your 10 year pump the brakes :D
mc1.webp
mc2.webp
 
Thank you. That's just what I was looking for. I'll grab the truck back from the dealer tomorrow and take care of this one myself.
 
You can bleed the MC on the truck, it just takes a LOT more fluid to do. Ask me how I know (after running it dry)....


I swapped out my MC due to my own idiocy of using box end wrenches and screwing up the threads (in an attempt to bleed the MC as per the FSM instructions). Use flare nut wrenches on all the lines. If you strip it or round it, some of the hard lines will have to be shipped from Japan. I got the last one in the States on one of those. :D


Just out of curiosity, why do they say the MC is bad? When I swapped mine out, I got a used one with around 60k miles on it and compared it to my 150k one. The old one looked every bit as good of shape as the new one.
 
well I bent one hard line a little too far and it pinched at a bend. I took it to ORME Bros. right by me and they bent me up a new one and flared it with the old fitting for under $50. Took them just a few hours til I could pick it up.
 
well I bent one hard line a little too far and it pinched at a bend. I took it to ORME Bros. right by me and they bent me up a new one and flared it with the old fitting for under $50. Took them just a few hours til I could pick it up.

IIRC mine was only something like $14.

Still if I needed it right away, I would have gone with the $50 option. :)
 
I picked up the truck today. The brakes are worse and it is difficult to stop with only one push of the pedal. I have to pump it, but I made it home slowly and safely. A new MC, as well as plugs, rotor, cap and wires have been ordered to start baselining. Wheel bearing repack, air filter and coolant change have been done recently.

Just out of curiosity, why do they say the MC is bad? When I swapped mine out, I got a used one with around 60k miles on it and compared it to my 150k one. The old one looked every bit as good of shape as the new one.

Something is not right, because I can't stop. The dealer just changed the brake fluid for me. The brakes didn't seem right when I got the truck back, so I brought it back in. I thought maybe they left some air in the lines. They bled the lines again, then determined that air was being drawn into the system through the master cylinder. I'm taking their word that that is where the leak is. The brakes have gone beyond spongy and are downright dangerous now.

Thanks for the tip on the wrenches. :wrench:I'll have to get some of those.
 
Last edited:
Also, how do you bleed the MC on the bench? Is it described in the FSM? I should have that soon.
 
Something is not right, because I can't stop. The dealer just changed the brake fluid for me. The brakes didn't seem right when I got the truck back, so I brought it back in. I thought maybe they left some air in the lines. They bled the lines again, then determined that air was being drawn into the system through the master cylinder. I'm taking their word that that is where the leak is. The brakes have gone beyond spongy and are downright dangerous now.

Got to be honest, I really don't think its the master. Have you checked all of your rubber lines? When I did my brakes a few weeks ago I found an almond sized bulge when the brakes here pumped. Its what was the cause of MY spongy brakes.
 
I think you have a leak in the system and doubt the MC will fix your problem.

:hhmm: Any advice on how to track this down before I throw on a new MC? I will now take a closer look, but I don't see any fluid leaking, and the MC reservoir is still topped off.
 
Look at brake hoses and bulging. Look for air bubbles when pumping the brakes. Did you check the rear as well?
 
The FSM has a nice procedure for finding issues with soft brake lines--using a mirror behind the brake line to see bulging and the like.

That said, brake issues seem so finicky with these trucks--especially with the ABS and the LSPV which is so prone to rust.

I got rid of the LSPV from the rear, got rid of the ABS box, ran my own hard lines, added a manual proportioning valve and the brakes work like a small Honda vehicle....nice and smooth. Personally, I like my brake modifications (including rebuilt rear calipers and new fronts).

By the way, I would NOT recommend what I wrote above...caution at your own risk.

-o-
 
If the brake lines are bulging somewhere, would I see a drop in the fluid level of the MC when the brake is depressed?
 
FWIW it doesn't sound like a bad MC to me either.

Here's what I'd do. Take the truck out to an empty gravel lot, and pull the fuse for ABS (to disable it). Get up to a decent clip, and slam on the brakes and see which tires lock up. You may need a spotter/observer to help you tell.

That at the very least should (hopefully!) give you an idea of which brakes are running soft, and may help narrow down your search. At the very least it should tell you if the problem is front or rear.


It really sounds like air is getting in the lines though. I'd definitely bleed the brakes again, making especially sure you hit the LSPV. I've found on mine that sometimes air can collect up at the LSPV (since it's a high point in the brake system) even after I think I have it all out. I usually bleed the LSPV first, follow the FSM procedure for bleeding, then bleed the LSPV again for good measure (shouldn't have to bleed much, just enough to tell you that there's no air there).

Also when you bleed if you have a clear hose you can see where the air is at. That might give you an idea of where the air is being introduced as well (IE: if no air in the front tires or LSPV, but air at the rear tires, then you know the leak must be behind the LSPV).

HTH



By the way, I would NOT recommend what I wrote above...caution at your own risk.

Yes...Beno does things a bit.....differently. :p

I don't think there's any problem removing the LSPV for those with drum brakes (mostly 91/92), but personally I think it falls in the category of "a bad idea" for those of us with disk brakes. :meh:
 
FWIW it doesn't sound like a bad MC to me either.

Here's what I'd do. Take the truck out to an empty gravel lot, :

Not too much gravel here in the middle of the city. I might be able to find a construction site nearby.

I don't know a thing about brake systems (actually I know what the LSPV is now ;)), but I'm assuming the engine needs to be running for the brakes to work, and someone pumps the brakes to pressurize the system to create a bulge (or air leak) in a line somewhere. Then someone else must track down that bulge or leak.

In my first cartoon bubble I see :princess: standing on the brakes while I crawl under the running truck to find the leak. Next thing you know she is on a sandy beach with the State Farm Agent and a large bag of money, trying to forget about "the accident".

In another episode I see my buddy holding down the pedal while I'm under the truck tracking the hoses. After a long and tedious process I find the bubble just as it bursts and sprays fluid all over.

Sound about right?
 
Last edited:
In my first cartoon bubble I see :princess: standing on the brakes while I crawl under the running truck to find the leak. Next thing you know she is on a sandy beach with the State Farm Agent and a large bag of money, trying to forget about "the accident".


Well.....that's why I'd rather test it myself on some gravel.


Last time I had to crawl under the truck (to adjust the linkage to the tranny, so it'd go into park easily) I needed the :princess: to hold the shift lever all the way forward while I adjusted it. I think she was about ready to run me over after the fifth time of me saying "don't touch the e-brake!" and "stand on the brake pedal!"

(Not that I don't trust her, but I am not fond of being under a 6000 lb truck while someone's at the wheel.)
 
I've now got the new MC in hand. The FSM suggests adjusting the length of the booster push rod before installing the new MC. There is a special service tool to measure this, which I don't have. Should I get this tool before installing the new MC?
 
Back
Top Bottom