newbie could use some help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 20, 2014
Threads
5
Messages
31
hey guys hope all is well. finally picked up an 80 been looking around for a while and decided on a 92. the wife and I spend a lot of time outdoors and with a baby due anyday we needed something bigger than my wrangler so had to let her go for something bigger. my dad has always been a cruiser guy building fj40's up in wa so he was pleased to see the new ride and said it was right where it was supposed to be parked in front of a jeep meaning the neighbors Cherokee. but I need to get her running up to par. when I picked it up it was running real rich and finally had a chance to start checking it out I found the harness running the length of the engine was burned in a few spots so spent the afternoon repairing some wires an got her running a lot better but still rich and after driving around a little it started to run even richer again and losing power. I stopped and parked it a little while after about 30 min it ran fine again for about 10 min and started idling low and loss of power again. ive been searching for days on the site and haven't seen anything to really point me in the right direction. I would definetly appreciate any help I'm a collision tech with many years building custom cars so I'm very mechanically inclined not too big with electrical but can get by. would like to pick up a manual to be able to research anything can I pick one up from Toyota or any other good places to find one? well prob boring you by now so have a great nite and anyone willing to help i'll try not to write a book on the next reply tanks again
 
Get an electronic manual for it, search the forum and they are for sale on here. I like mine! Is your check engine light on? kinda sounds like a very bad O2 sensor. When they go bad, the computer will make the fuel mixture rich as opposed to lean. Safer that way.
 
Im thinking you still have a bad wire somewhere causing the injectors to stay open. Keep checking the harness even up under the intake. Then wrap the whole thing with heat tape. Mine did the same because of a small bad spot were it laid against one of the egr tubes. It got worse and worse till I couldn't drive it
 
I belong in the 60 series section, so please excuse my ignorance here... Is this still the fj80, with 3fe? If so, I just solved one doing the same...
Believe it or not, new cap and rotor solved the exact intermittent running problems on a fj62.
 
Year of the truck would help. I'll plug in the usual answer here too, have the O2 sensors been replaced?
 
Good place for a manual and lots of other good info for 91-92.
http://www.sdsysdesign.com/tlc/fsm.html

First thing I would check is for stored codes.
Then check the intake boot, they crack in the accordion folds.
Cold start timer or injector could be a possible issue.
O2 sensors.
Vacuum lines.

I would definitely start with a baseline tune up and make sure that is all good before going in to deep.
 
thanks for the help. it's a 92 and o2 sensors are gonna be ordered prob Monday if the wife doesn't pop. the burn spot was under the manifold against the egr tubes had to order new manifold gaskets and tune up kit no one in Denver had one thought that was weird so gonna always order two of everything for backup. but got in there an fixed what I could get to. is there a sensor along that harness like a temp that could make it run rich. no engine check light either and not sure yet how to find codes. I've been searching through the forum but there's always alotof stuff that pops up and haven't had much time to sit and go through all of them to find what im looking for. again thank you very much i'm always willing to help any way I can.
 
hi again ok so just replaced the o2 sensors cap rotor wires plugs she's starting to run better but still running rich just not as bad drove it a couple days and now the radiator has a leak looks like someone tried to epoxy the lower tank so gonna have to get that fixed but she seems to start running richer or worse anyway after I drive a few miles when its cold seems to run good. is there a sensor that might make it run richer with temp control? still waiting for the wife to pop so haven't had a lot of time to spend on it just a few min here an there. might order a fuel pressure regulator tomorrow. will go through and pull the intake and go through the harness when I have time to do it in a day. thanks guys
 
well the symptoms are she has black smoke coming out the back at idle im getting closer and she's running better but still a little bit after a few miles of driving she losses power ive replaced the 02s,cap and rotor,wires, air filter ,plugs, I found some burnt wires along the intake and repaired as much as I could see without removing the intake thinking about pulling that this weekend but the lower rad tank started leaking looks like someone tried to jb weld it so gonna remove that and re solder that this week when possible so I can drive it again. just got home after a few days in the hospital with our baby girl and have to catch back up at work starting tomorrow but would love to get this straightened out asap the wife has already planned a camping trip with friends in a couple weeks. is there a temp sensor that would cause a rich fuel mixture im not afraid to change sensors cause they prob need it anyway and want spares to take with on back country trips anyway. any help would be greatly appreciated thanks
 
thanks and yeah she's a real trooper took many years to find one hot,tough and willing to put up with me. took the intake off to fix the harness had about 6 wires burned and broke got them all soldered up and ready to put back together just need the time working 12hr days and helping with the new baby has slowed progress but will atleast get back on it sat after work of course. if this takes care of it lift and tires next
 
morn guys so I just got done putting the 80 back together still rich but hey I have a check engine light on now must have fixed something and checking the afm it looks as though the po pulled the screws and tried to unhook it that way so looks like I need one of those im curious if one from other years or models will work a friend at work has one from a 92 4runner and I can get one from a 96 lc I haven't had the chance to look at them yet just curious if anyone has tried one. on another note excited t check the cel codes but have to go to a bbq so some friends can see the new baby first would appreciate any info thanks guys
 
Welcome to the forum. To help us out in reading your posts, could you put in a little punctuation?

I'm in Denver as well and we have a good group of tech support within the rising sun 4x4 club, you should check us out since we're local to you. We have a couple 3FE gurus as well. Rally next Saturday.

I've broken a maf before so know that pain. There are a few options in Denver besides your typical pick and pull place. Jim's got parts in north Denver *might* have some 80 stuff though he mostly deals with trucks. Classic cruisers in salida has always been helpful as well. I would not expect mafs from any other vehicle or year to work-on my 91 pickup there were two different mafs available that had their signals completely reversed!


...via IH8MUD app
 
sorry, I'm not the most punctual person but i'll try to clean it up for ya. thanks for the info. jim gave me the number to classic cruisers and merle was very helpful. they had what I needed. it's on the way hopefully my parts guy at work didn't order one for me as well,or i'll have a spare. I'm very interested in checking out the rally Saturday. thanks guys
 
Back
Top Bottom