Newbe axle question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 31, 2007
Threads
3
Messages
210
Location
Tucson, AZ, USA Age:59
Ok, I'm going to look at a couple Fj/FZJ 80's this weekend.
I've pretty much decided that this is the route that I want to take over the current '95 4Runner that I own now.
I've just, barely, started mods on the 4Runner, having never even thought about the FJ's before and then, last week, something caught my eye about them (things like the solid front axle, though less than desirable Birfs and radius CA setup ;), available factory lockers on the FZJ's, etc).
I have a question regarding the axles. A search on my part didn't yield the answers, but I probably just didn't look hard enough ;)
What axle's do these have, front and rear.
It appears (I've haven't even looked at a "live" one yet ;) ), that they have a HP Toyota 8" for the front, but what's the rear, an 8" also ? I found (maybe a like from one of the stickys) a writeup on installing an Aussie or LockRite (can't remember which and they're about the same) in the rear of an '80 and it appeared to have a diff cover.
The 4Runners don't, they have a drop out 3rd, as I'm sure everyone knows.



Thanks,
Fred
 
The 80's have a HP 8" with much beefier/stronger birfs than the pickup/FJ40/60, etc in the front. The rear is a larger drop out type cruiser diff, no removable covers.
 
The rear is a "Toyota 10 bolt" if you want to call it that. I think it is a 9.5 inch ring gear. Same differential that is in the 40s, 55s, and 60s. Plenty strong.

David Sword
 
The rear is a "Toyota 10 bolt" if you want to call it that. I think it is a 9.5 inch ring gear. Same differential that is in the 40s, 55s, and 60s. Plenty strong.

David Sword

Ahhh, sorry, meant to say "10 bolt", must've been thinking the 'ole 14 bolt domestic ;)
That would be the same axle then, used in the Dwarf cars (racing).


So the birfs on the '80's are less of a concern than those on the P/U's.
We've been on a couple of runs, a few years ago, when I had the Jeep, with some Toy P/U's (don't know years, etc., as I wasn't paying any attention to Toyota's at that time) that snapped birfs.
Kinda messy ;)



Thanks again for the information,
Fred
 
The 80s will still snap birfs. Usually happens when wheel is turned hard and backing up.

David Sword
 
The 80s will still snap birfs. Usually happens when wheel is turned hard and backing up.

David Sword

Didn't mean to imply that the birfs were bullet proof, but they are stronger that those on the P/U's ?

Regarding upgrading 'em, Longs or the birf elimination kits ?


Thanks again,
Fred
 
The 80 series birfs are stronger, but the truck is much heavier than a minitruck. But many who break the birfs on minitrucks are running large tires and low gears through manual trannys that put alot of stress on the birfs. An 80 with an auto tranny and running 35s or less will put less stress on the birfs. The Longfields are stronger and almost unbreakable but, due to their hardness, do not stand up as well to the high mileage of a daily driver and actually wear faster than an OEM birf.

David Sword
 
80 Series birfs are rarely broken. The most common "issue" arises from neglected service and they are allowed to wear from lack of lubrication.

"Trail breakge" usually surfaces when tire diameter exceeds 35 inches and the vehicle is operated in a very agressive manner.
 
Back
Top Bottom