new speakers = blown amp??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 5, 2006
Threads
127
Messages
745
so i installed a set of JBL 6 1/4" in the front doors of my truck.. the fit was ok, install went ok. The sound is amazingly better.....

but as soon as i started driving the truck, the sound totally cut off.. not only from the two new front speakers, but all speakers in the truck stoped producing sound. The deck still functions, just no sound is produced.

So im guessing i blew up my amp? blew a fuse in the amp?..... am i correct?

So should i replace the amp? where is the amp in my truck?

Any help would be appreciated.

Cheers
 
With the shallow mounting depth in the doors, I would verify that the + & - posts on the back of the speakers are not touching metal. In tight mounting locations, I usually wrap the posts with duct tape to make sure they don't touch anything.

I have seen cases where with just one speaker grounding out, it can effect the sound from the rest of the speakers.

Pull all speakers out and verify that the connections are free. I believe the amp is located behind the rear, US passenger side panel in the cargo area.

All of that said, I had a local stereo shop install my stereo (I offered to detail the owners car in trade). Alpine head unit and Diamond Audio 6.5" front doors and 5.25" rear doors. After reading about some of the trouble others have ran into due to the mounting depth in the doors, I decided to let a professional do the work.

Riley
 
The amp is behind and above the PS speaker in the dash next to the glove box. Don't know what ohm value the factory speakers are, but if the aftermarket ones are lower it could overload the amp.
 
so should step one be to duct tape the backs of the speakers....

step 2 check out the amp? .... how can i tell if there is damage to the amp.
 
It is VERY common for stock speakers to be a different resistance (Ohm value) than after market speakers. After market car speakers are typicaly 4 ohm but stock speakers could be anything at all. If they are a different resistance than stock then you stock amp may not work with them. Use a DMM on the stock speakers you took out to see what they are.
 
so should step one be to duct tape the backs of the speakers....

step 2 check out the amp? .... how can i tell if there is damage to the amp.

Not knowing much about the amp (obviously), I would pull the new speakers out of their holes, still connected and then see if there is any change when turning on the stereo. That to me would be the easiest place to start. If no change, then hunt down the amp and see if it is sending out a signal.

Like mentioned before, most aftermarket auto speakers are 4 ohm but the factory ones could be different. The change in ohm load on the amp with the addition of the new speakers could have caused the trouble.

Instead of changing the factory amp, just find a decent, aftermarket head unit. It will have plenty of power to run the door speakers and I know it will be cheaper than a replacement factory amp.

I would say to check your head unit ground, but I assume you did not touch it during the speaker install.

Riley

Riley
 
If the deck is still lighting up and functioning other than sound, the ground is probably still good. Most likely the difference in speaker resistance has caused the trouble. Pull the wires on the new speakers and see if the amp comes back on line. If it does, then the speakers are just overloading the amp. As Riley said, buy an aftermarket deck and bypass the amp. You'll get better sound quality out of the deck, and as you replace speakers it will just get even better.
 
It is VERY common for stock speakers to be a different resistance (Ohm value) than after market speakers. After market car speakers are typicaly 4 ohm but stock speakers could be anything at all. If they are a different resistance than stock then you stock amp may not work with them. Use a DMM on the stock speakers you took out to see what they are.

:rolleyes: The door speakers are 4ohms (printed right on the back), except for the rear roof tweeters, they are 25ohms. The tweeters are directly spliced in parallel to the door woofers. Which means the amp "sees" 1/2 of the least resistance, which would be 2 ohms on the front speaker set and 3.5 ohms on the rear door set. Adding aftermarket speakers should have no effect, even if you disconnected the factory tweeters and the amp got only 4ohms f/r.

As for the initial problem, you had to short the amp. Which if your head unit turns on is bad news since they are both on the same fuse. Unless the amp has a built in protection circuit, which could be 50/50. Check your speaker connections and try again.

Right now I'm in the process of putting an aftermarket amp in place of the stock amp. It's really easy to do and even using the stock door woofers, will sound better than aftermarket speakers on the stock amp.
 
Last edited:
There is a different between theory and reality. All these Ohms differences in speakers at such low wattage are not going to shut the amp down. I would bet money that your speaker is shorting against the door panel and it is causing the amp to clip and then power down. Your amp may be just fine. You need to address the short first. Then you can go on to diagnosing amp problems. I might have the amps laying around somewhere if you get to the point that you think you need them. I know I'm never going to use them again.
 
i do have an aftermarket head unit... maybe its still running through the amp...
 
i do have an aftermarket head unit... maybe its still running through the amp...

Depends.....There are TWO styles of stock head units that can be connected. The smaller pin single connector style uses the amp next to the gove box because that style headunit DOES NOT have a built in amp. The large pin double connector type head unit, the one aftermarket jumper harnesses are sold for, HAS a built in amp.

Both stock harnesses are there and BOTH run to the speakers. If you had the stock head unit that used the external amp but YOU used the large pin double connectors to hook up your aftermaket unit, then the amp is NOT being used at all.

You have a speaker line short and your aftermarket head unit has a built in protection circuit.
 
speakers ended up being ground out on the window harness..... duct tape to the rescue and the truck sounds great.

Thanks mates.
 
I recommended checking the + & - first because I just went through all of that a few years ago. My father-in-law's 1963 Porsche 356B needed some new speakers and he decided to go with 6.5" in the kick panels (very shallow). He had already converted it from 6 volt to 12 volt so we were all set. I wired up the speakers and they worked fine. I installed them in the kick panels and turned everything back on and no sound. Scratched my head and decided to start again. After about 3 attempts, I just left the speakers playing and started to install them and realized that the + & - were grounding out against metal. Wrapped the terminals in duct tape and all was good.

Good to hear that it was the same problem for you (free fix).

:cheers: Riley
 
yeah i had to space the $hit out of them, and used the JBL speaker covers... i couldnt see any other way. I got the speakers for $50/set.

Going to do the rears soon, and maybe do that sub thing that some guys are doing on here with a new amp.

ill try and post pics next week
 
Back
Top Bottom