New Cruiser, But Some Problems

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 14, 2007
Threads
2
Messages
50
Location
Rigby, Idaho
I'm new to Toyota's and the IH8MUD forum (first post), but really looking forward to becoming familiar with the "new" 1996 I just picked up. Has 102,000 miles, and I'm the third owner. Other than routine oil changes, I can see that some of the maintenance has been neglected, but it has never been off road (no lockers).

I'll be baselining all of the fluids, and so far I've researched the forum and completed the transmission fluid exchange, motor oil/filter change, and have purchased the Toyota Red (at about $35/gallon here in Hawaii), along with a Prestone flush kit, and will get this done before I put any more miles.

Started to do the differential oil change today, and after pulling the back plug, the fluid looked decent. When I pulled the front, a thick goo started running out. I'll be calling CruiserDan tomorrow to get his advice on parts. I'm new to working on cars, but the Cruiser will be used primarily as a beach truck, and I'm in no rush to complete repairs, and can see there is a wealth of info available to me.

There are also other projects I want to get completed, including new belts, hoses, thermostat, fix front driver's side window (does not roll down).

Enjoy reading all of the posts. I plan on owning this truck for a long time, and I can see how everyone gets addicted.
:cheers:
 
Welcome to the forum!

These guys who'll be chiming in are a great source of information. Have fun!

-Eddie
 
When I pulled the front, a thick goo started running out.
:cheers:

You may be getting grease from the knuckles in the front diffrential. At the top front of the knuckles, there is a square head plug, 12mm I believe. Remove those and stick a clean screwdriver, piece of wire, etc down to measure the amount of grease and consistency. Before removing the plug, clean the area, you dont want to get dirt conamination in your birfields. Those cavities should be about 1/2 full of grease and it should be thick like grease. This should give you an idea if your inner seal is bad.
 
Welcome,
man I miss vacation in OAHU.
Are you hearing any clicking when you make full turns?
That goo sounds like the seal is gone.
Get the parts from CDan for the rebuild.
Read then read some more, ask questions, get the tools,
a helping hand and go for it.
Good luck.
 
Welcome! Curious, what color was the goo? Tan?

As tech_dog said in another newb thread,

Here's a good place to start: https://forum.ih8mud.com/showthread.php?t=84888

You may be getting grease from the knuckles in the front diffrential. At the top front of the knuckles, there is a square head plug, 12mm I believe. Remove those and stick a clean screwdriver, piece of wire, etc down to measure the amount of grease and consistency. Before removing the plug, clean the area, you dont want to get dirt conamination in your birfields. Those cavities should be about 1/2 full of grease and it should be thick like grease. This should give you an idea if your inner seal is bad.

Thanks everyone for the input. I'll crawl under take a look at this and let you know what I find. There isn't any clicking noise that I can hear when I turn the wheel full in one direction. Also, the grease/oil is more of a med-dark gray, versus tan in color.

Since I plan on having the vehicle for a long time, I'm inclined to just order up the parts, and try and pound out the job over a weekend. For me, doing this type of work is a nice break from my day job, and I think I'll really enjoy wrenching and doing all of the reading and research.
 
Welcome,
man I miss vacation in OAHU.
Are you hearing any clicking when you make full turns?
That goo sounds like the seal is gone.
Get the parts from CDan for the rebuild.
Read then read some more, ask questions, get the tools,
a helping hand and go for it.
Good luck.


Next visit to Hawaii, try and get to one of the other islands. I have to travel to Honolulu about once every 1-2 weeks, and it is always nice to get back to the Big Island. There are some nice beaches here that are only accessible by a long walk, or 4 wheel drive.

Aloha
 
Since I plan on having the vehicle for a long time, I'm inclined to just order up the parts, and try and pound out the job over a weekend.

That's your best approach. No matter how much grease is in the knuckles, it's time for a repack.

-Spike
 
Wheel bearings rarely need replacing. I wouldn't assume you need new ones until you open it up. If it had 200K miles on it I'd throw a set of bearings in there just because you wouldn't know how the maintenance was done.

-Spike
 
Wheel bearings rarely need replacing. I wouldn't assume you need new ones until you open it up. If it had 200K miles on it I'd throw a set of bearings in there just because you wouldn't know how the maintenance was done.

-Spike

Called up Cruiser Dan today (great guy!) and ordered up $810.00 worth of parts, plus another $85 for 2nd Day shipping. I think it was a VERY fair deal, especially since I'm confident CDan will provide me with the right parts, etc. (also purchased the FSM at the place he recommended, which set me back another $106.00, including express shipping).

I was going to buy new wheel bearings, but he advised, as you did Spike, that I should wait until I tear into things, and then I can make a decision. If I need to purchase, I'm hoping I can purchase at the local Toyota dealership, or can have CDan FedEx them to me.

So, for my 102K Cruiser, I ordered, among other things:

All new water hoses (CDan saved the day, when he thought to ask if my Cruiser had a rear heater....it does not, as it was purchased new here in Hawaii, and the temperature during the day rarely goes below 70 (that is, unless you are on the top of Mauna Kea, at 14,000 feet) Apparently the vast majority of mainland purchased Cruisers are ordered with the rear heater.

Replace all belts

Front axle service "kit" (assume this would not include the knuckle job? What more whould I have to purchase?)

Rear axle Service Kit (including 50'something mm socket)

New T-stat, and radiator cap

3 of the Japanese sourced oil filters (get 'em while their hot! Recall CDan giving an opinion that they are better than the Thailand sourced filters, and the price from Dan for the Japanese sourced filter is less than I can get the Thai filter over here.)

Air Cleaner

Rubber 'hose' that goes from the throttle body to the air cleaner (old one cracked - $70.56)

Plugs, Cap Assy ($10.65), Rotor ($6.15) , "Cord Set" ($84.64)

New PCV valve, grommet, two hoses

OEM Wiper Blades

F/R Pads (will upgrade to 100 series down the road for the front, if I ever need to get new rotors)

Also, as mentioned earlier, will baseline all fluids, including Toyota Red for the radiator.

I will be reading, and reading, and reading, to try and prepare for these jobs, especially the axle service. Wish me luck!

Aloha
 
You have quite a bit of work ahead of you. Take your time and do it right the first time. Plan something simple for the first weekend (cap, rotor, plugs and wires) and see how it goes. I know that after I finished my first PM (front brakes, belts & oil/filter), I had a pretty good list of additional tools I needed to get.

Just do not get overwhelmed by everything. When I purchased my '94 about 2 years ago, the front differential was full of gray goo. I drained and filled but it turned gray again after a while. I have been checking and filling the birfs until I get the time to tackle the front axle service.

Keep reading and print out the threads so you have a copy that you can get dirty while you work.

Best regards and welcome :flipoff2:!

Riley
 
Riley,
Thanks for the advise.

Last night, when draining/filling the front diff, I could only get about 1.75 quarts of oil in the front diff, about a quart less than specified. In order to remove some of the goo which is apparently still in there, and not allowing me to fill closer to factory spec, I'm wondering if anyone has left the drain plug off, and then tried to place some type of solvent in the diff, letting it run through to a drain pan (hopefully carrying with it some of the heavy contaminated grease/oil). From there, plug the diff, and try filling again.

Or, should I not worry too much about the approx. 1 quart I couldn't get into the diff (keeping in mind this is not a DD), and simply ensure the knuckles have grease (by the way, do you know of a link/picture showing where the grease is inserted? Have not received the FSM yet. Also, what type of grease are you using to fill the knuckle with your grease gun.)

Again, great advise on not trying to take too much on at once. I have two high school boys, and together we are all seeing what happens when service is neglected. Also, we are having fun out in the garage. Amazing some of the conversations you can have when wedged under a truck.

Aloha
 
If you remove the tire you should be able to see the plug. It is right next to the ABS sensor and has a square top. It is on the top of the knuckle, inboard of the brake rotor shroud, slightly off center. As mentioned before, clean the area before removing to avoid getting any contamination in there. Chose a brand name grease that contains Moly (Molybdenum) for the birfields. Use a wire tie as a dipstick and fill the birfield cavity no more than 2/3 to 3/4 full.

My son is 10 years old and helps with what he can. I set all of the tools out on a table and he acts as my gopher. He is also getting pretty good with the digital camera (I try to document as much as I can on all of the PMs).

:cheers: Riley

P.S. Read this thread https://forum.ih8mud.com/showthread.php?t=11224 and there is a picture of the plug. Also, I would not run any type of detergent in the axle. I do not have any scientific reason for not doing it, I just would not do it. Far too many parts in there to get screwed up.
 
Last edited:
Kona Joe,

I get over to the BI about once a month on work myself. If you ever need a hand let me know. When the super ferry gets going I might think about shipping my rig over from it's "dry dock" in SoCal. Not many places to explore on my island, unlike BI.

Best of luck with the rig,

-Matt
 
Riley - Got it and thanks. Will work on that tonight after work.

Matt - I read the Superferry won't travel to the Big Island until sometime in 2009. Kinda' a good/bad news kind of situation. Will be fun to load the Cruiser on the ferry and head to Oahu or Maui, but that also means a lot of people coming to the Big Island. You are not the first to comment to me that the only place in Hawaii to really get some open stretches of road (relatively speaking....I used to live in Nevada) is over here. Thanks for the offer of help. Hope I don't "need" it, but nice to know you are out there.

Aloha
 
Back
Top Bottom