New Brakes & weirdness

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 4, 2006
Threads
449
Messages
14,193
Location
NorCal
I finally (I thought) got my brakes working perfectly. I've got about 200 miles on my '78 40 since I finally got everything adjusted and working. I've even gotten to where I don't bring my tools everywhere. All the parts are new except for the hard lines.

Today on the way to the gas station :crybaby: they were hanging up a bit. I decided it was my imagination. Down the road a bit I could tell that I was having to use more gas than usual to keep it going, so I pulled over, and sure enough, the front calipers were hot, so I turned around to get my car. It was about 5 miles home, but before I got there I noticed at a stop light that they were back to normal.

I drove it to work instead of giving up, and it's ok.

WTF? Some little particle keeping it from releasing?

I'll bleed the fronts again tomorrow to see what the fluid looks like.

I almost hate to mention (again) that I'm the experimental poster boy for "will Toyota brake parts stand up to DOT 5 silicon fluid". This will only worry me if they get mushy from the MC seals going bad, or leak from the calipers or cylinders.
 
Last edited:
Fast Eddy said:
I finally (I thought) got my brakes working perfectly. I've got about 200 miles on my '78 40 since I finally got everything adjusted and working. I've even gotten to where I don't bring my tools everywhere. All the parts are new except for the hard lines.

Today on the way to the gas station :crybaby: they were hanging up a bit. I decided it was my imagination. Down the road a bit I could tell that I was having to use more gas than usual to keep it going, so I pulled over, and sure enough, the front calipers were hot, so I turned around to get my car. It was about 5 miles home, but before I got there I noticed at a stop light that they were back to normal.

I drove it to work instead of giving up, and it's ok.

WTF? Some little particle keeping it from releasing?

I'll bleed the fronts again tomorrow to see what the fluid looks like.


If there was air or water trapped in the front it could cause what you are talking about....




Fast Eddy said:
I almost hate to mention (again) that I'm the experimental poster boy for "will Toyota brake parts stand up to DOT 5 silicon fluid". This will only worry me if they get mushy from the MC seals going bad, or leak from the calipers or cylinders.



Having read about the different brake fluids, I have yet to find anything that sells me on the virtues of Silicone based brake fluid, compared to Glycol based, especially in a Land Cruiser. Fine the boiling point is higher. If you are boiling your DOT 3 or 4 brake fluid, you need to either fix the brake problem, or adjust your driving style before you hurt yourself of someone else. As far as the moisture absorption issue is concerned, taking ten minutes with a friend and flushing the system once year is not that troubling of a task in the event that you think that you have moisture issues in your fluid, and only helps with the prevention of bleeder screws seizing in calipers and wheel cylinders.


To each their own.



Good luck!


-Steve
 
Poser said:
I have yet to find anything that sells me on the virtues of Silicone based brake fluid, compared to Glycol based, especially in a Land Cruiser.

Old corvette guys don't drive their cars every day, and the calipers are usually the first thing to go, due to rust from moisture absorbtion. I was one once upon a time, and I got the idea stuck in my head.

When I went to the auto parts to get my fluid, I didn't think about it much. Certainly not enough. Now that it's in there, it's hard or impossible to get out, from what I've read. All my parts are new, and I'd have to fully tear them apart including all the seals and probably replace all the hard lines. Now that it's done I'll wait until a seal fails first.

Dayton and the other US rebuilders say their stuff has been DOT 5 compatible or at least safe for 20 years. I'm kind of hoping that Toyota is too. Like I said, I'm the experiment. If it goes well, I'll never have to change the fluid again, nor will my kids.
 
Poser said:
There is not a hydraulic component on that vehicle that will outlive you or your children....;)

Certainly not if left to rust, but just maybe if they're all full of rust preventative fluid. Maybe. :confused:

My uncle's '69 vette has had the same brake parts and fluid for over 10 years. I don't know if it's good as new though.
 
Back
Top Bottom