Need help diagnosing my A/C

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 26, 2006
Threads
24
Messages
150
Location
Fullerton, CA
I bought a '95 with 200K on the odometer three weeks ago and so far I am really loving it. It rides great and feels so nimble compared to my double cab Tundra. It does have a lot of miles though, and so I've been doing a lot of research here to find out how to fix all the broken items.

It has started to heat up here in So. Cal. the last week, and so now the A/C has been pushed to the top of the list. When I bought it, the temps were still cool outside and so the A/C seemed to work ok. But when I turn it on now, it blows cool for a few minutes, then gets warm again. So, here I am on a Saturday trying to diagnose in my driveway.

I have a set of gauges, so I hooked them up and started the engine. The high side read 240-ish and the low side is 40 - within specs according to my gauge set. Then, right about three minutes in, the low side suddenly drops to 0 and that's when it stops blowing cold in the cab. After that the high climbed to about 300, and that's when I shut it off.

Does this mean the compressor is bad? Or maybe a pressure switch? What else can I do to test? TIA for any help, this forum is a great resource.

-Chris
 
Search "fan clutch". You can rebuild yours (if necessary) for $10. If you drive a lot of stop n go (or slow wheeling) in high temperatures, you might want to consider an auxilary pusher fan as well.

Have you checked the belt condition and tension?
 
Search "fan clutch". You can rebuild yours (if necessary) for $10. If you drive a lot of stop n go (or slow wheeling) in high temperatures, you might want to consider an auxilary pusher fan as well.

Have you checked the belt condition and tension?

Cooling was actually my first thought, and I have read about the various cooling mods available. But even when driving slowly, my coolant temp never rises above 200F. And it seems like something must be wrong with the A/C system, when the low pressure drops to 0 and stays there.

-Chris
 
How are you monitoring your coolant temperature?

There's a way to test your fan clutch. Can't recall what it is, but my guess is that if yer Cruiser has a bunch of miles on it, this would be a good and cheap place to start (plus it's easy;)). Rebuilding your fan clutch with heavy weight oit (10,000cst) certainly won't hurt anything. If it isn't your problem, when you get the problem resolved, this will help your AC blow colder.
 
The expansion valve is shot.
 
How are you monitoring your coolant temperature?

There's a way to test your fan clutch. Can't recall what it is, but my guess is that if yer Cruiser has a bunch of miles on it, this would be a good and cheap place to start (plus it's easy;)). Rebuilding your fan clutch with heavy weight oit (10,000cst) certainly won't hurt anything. If it isn't your problem, when you get the problem resolved, this will help your AC blow colder.

I'm using a Scangauge to check the coolant temp. Thanks for the suggestion on the fan clutch, it sounds like an easy way to boost my engine cooling.

-Chris
 
The expansion valve is still shot.
 
1-800-432-6668.

It is also listed in the bottom of each one of my posts if you should mis-place it.


:cheers:
 
Concur on the expansion valve. You mght try to back flush it before you rip it all apart.

Do I flush it with compressed air? Or do I need to force some sort of solvent through?

And if the flush doesn't work, how expensive is a new compressor? I wonder if I should change that too since I'll have the system evacuated. With 200K miles, it has to be near the end of its life by now.

Thanks,
Chris
 
You will want to use a solvent. You can buy a can of solvent at any part store. Once you put the solvent into the low side, chase it with compressed air back to the high side. You will want to have both lines disconnected at the fire wall to do this. Put your finger over the high side, then pressurize the evaporator from the low side. Once it builds pressure,which you will feel with your finger covering the high side, release the pressure. Repeat the process several times. Watch your eyes and use a rag. That stuff stings like a mofo when it gets where it doesn't belong.

It doesn't sound like your compressor is bad, but you can drain the oil out and start fresh if you'd like. It certainly won't hurt. A new compressor can be had for $200 or so.

Just in case you didn't know, the fat hose is the low, and the skinnier of the two is the high side.
 
No cooling with a full charge. The valve fails to open and it blocks off the system. If you do not attempt to use the A/C for a few days the pressures will equalize accross the low and the high sides. If you turn it on it will cool for a couple minutes until the low side gets sucked dry.
 
You might also want to check to see if adding a little refrigerant solves the problem. Not sure of the type in the LC's , but most expansion valves operate on a prinicpal called "superheat". This is the amount the refrigerant is "heated" after all the liquid refrigerant in the evaporator is vaporized. The expansion valve is typically fitted with a remote bulb that senses the refrigerant temperature leaving the evaporator. It then meters refrigerant into the evaportor to maintain the factory superheat setting which is usually anywhere from 8-12F. This is to ensure that no liquid refrigerant enters the compressor which could damage it over time. When the expansion valve or "TX" (thermo-expansion) valve closes (i.e. drop in suction pressure & increase in discharge pressure), it could mean that there is insufficient refrigerant (low charge) being feed to the evaporator, and therefore the TX valve tries to limit the amount of superheat in the refrigerant leaving the evaporator (i.e. all the liquid refrigerant has boiled/ vapourized too early as it passes through the evaporator and there is just refrigerant vapour travelling through the remainder of the evaporator coil which does not provide any cooling effect). For an expansion valve to seem work for a while (3 minutes), and then stop would mean to me that the valve itself may not be broken. Just my .02 cents.
 
No cooling with a full charge. The valve fails to open and it blocks off the system. If you do not attempt to use the A/C for a few days the pressures will equalize accross the low and the high sides. If you turn it on it will cool for a couple minutes until the low side gets sucked dry.

Mine did about the same thing but the compressor would stall and burn the belt when they bypassed the PSI switch to test. Mine only needed a complete cleaning. I still running the origanal EX valve. And now will run you out of there from being too cold.
Here in Cambodia every thing is fixable or rebuldable very little is just replaced with new parts. $6 they will rebuld car front end struts with all new seals and bushings and new oil.
They took my expansion valve apart the cleaned it. but dont know if any one in the USA can do that most just sell you new parts
brian
 
Last edited:
Ok, I ordered a new expansion valve and receiver dryer from cruiserdan a few weeks ago, but I'm just now getting around to installing them. Seeing as how the local shop will charge me $175 to charge it up after I change the parts, I'd like to try to do the whole thing myself.

I've still got some R134 in the system, where's the best place to empty it out? Do I just crack any line and let it leak out?

I understand that I will need to vacuum the system before charging, but I'm not sure what kind of pump to buy. Will THIS type of pump work? Seems to cheap to be any good. Or will I need one like THIS?

After I've held a vacuum for a bit to ensure there aren't any leaks, do I then hook up my gauge set and charge with R134a right away? What about adding dye, is that necessary?

Thanks,
Chris
 
Ok, I ordered a new expansion valve and receiver dryer from cruiserdan a few weeks ago, but I'm just now getting around to installing them. Seeing as how the local shop will charge me $175 to charge it up after I change the parts, I'd like to try to do the whole thing myself.

I've still got some R134 in the system, where's the best place to empty it out? Do I just crack any line and let it leak out?

I understand that I will need to vacuum the system before charging, but I'm not sure what kind of pump to buy. Will THIS type of pump work? Seems to cheap to be any good. Or will I need one like THIS?

After I've held a vacuum for a bit to ensure there aren't any leaks, do I then hook up my gauge set and charge with R134a right away? What about adding dye, is that necessary?

Thanks,
Chris

You are not allowed to just vent refrigerant into the atmosphere - it needs to be collected and recycled.

Either of the two vacuum pumps linked will work - the first needs your compressor running the second runs on electricity. Some say that the venturi type (compressor) pumps do not work as well.

You run the vacuum through the gauge set. After drawing a vacuum for half an hour close the valves to be sure that the system maintains the vacuum for 20 more minutes. Once satisfied you attach your R134a to the gauge set and start filling. Dye is only necessary if your system does not hold vacuum.
 
Back
Top Bottom