Mirror fell out. Replace or fix it?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 13, 2006
Threads
114
Messages
634
Location
West of the Pecos
I'm pretty sure I know the answer already... CDan. But just in case, is there a way to fix this? The plastic attachment points that hold the mirror in finally broke and the mirror fell out. All the damage seems to be on the mirror "module" itself - the little hooks etc in the mirror housing seem to be okay.

Also, assuming I need to replace the whole mirror "module", what order do the red, orange, and black wires plug back into the "module"? (I wasn't thinking about it until after I unplugged everything).

mirror2.jpg


mirror.jpg
 
Mine looked exactly the same. Tried glue, fell off when I slammed the door. I then used a small zip tie to attach a washer (OD 13/16", ID 7/16") to the remaining part of the broken plastic 'keyhole' on the mirror. The id of the washer was perfect to grab the hook in the housing and hold tight. No problems in 6 months...no wobbling, either. This is the DS mirror, so the door gets a lot of action. No pics, sorry.
 
Fixed mine with bits of epoxy and some stiff wire.

Looks to me that your screw slot at the bottom has broken off. That can probably be fixed with some paper clip wire, epoxy and the original screw. If you don't have the steady hands and patience, it's probably better to just buy a new mirror.


Kalawang
 
Mine looked worse and is still wobble free after following the write up on using caulk.
 
Yep, the ONLY attachment point on the mirror module itself that didn't break is the one keyhole you can see in the pic. I will check out the faq, but I thought that was only for a wobbly mirror rather than a fallen out mirror.

Again, does anybody know what order the red/orange/black wires plug back into the mirror???



?
 
Yep, the ONLY attachment point on the mirror module itself that didn't break is the one keyhole you can see in the pic. I will check out the faq, but I thought that was only for a wobbly mirror rather than a fallen out mirror.

Again, does anybody know what order the red/orange/black wires plug back into the mirror???



?

might be able to use the passenger side as a reference
 
Good idea! Why didn't I think of that?... too simple, I guess.
 
I used a left over screw from somewhere inside the car, and used it on the bottom of the mirror to stop it from wobbling. But you can try the JB-Weld way, and just make your own tab. You shouldn't have to buy a whole new assembly.
 
i dont remember on the wires, trial and error is my method. Try the caulk method before spending money on a new one, mine also had the broken screw hole on the bottom
 
I used JB weld on mine- it was the same condition as yours. For the bottom attach point I simply made a cylinder of jb weld wrapped with a bit of wax paper as form. After it cured I drilled and tapped it to accept the mounting screw. Worked great.
 
I used a plastic repair compound available at Pep-boys with the JB weld and similar items. I believe it is simply called Plasti-weld or something like that. Like others said you just form your own tab and then drill out the slots. Very easy fix - have a beer while the repair sets up
 
If you plan on keeping the truck just replace the whole mirror and be done with it. Most of the time these repairs will fail again. A shakey or missing DS mirror is a safety issue for me. With the CDan discount the price is not too bad. And, if I recall, they come already painted.

good luck
 
If you plan on keeping the truck just replace the whole mirror and be done with it. Most of the time these repairs will fail again. A shakey or missing DS mirror is a safety issue for me. With the CDan discount the price is not too bad. And, if I recall, they come already painted.

good luck


"not too bad" is a matter of opinion... I will say that the CDan discounted price is much less bad than the suggested retail price though!

A few hours after the initial sticker shock, and after thinking about all the ways to repair this using Devcon Plastic Steel putty (a lot stonger than JB Weld), I've about decided that since this truck gets at least 100 miles per week on ROUGH rock/caliche roads with all the associated rattling vibrations, I'd probably be better off to just bite the bullet and replace it... If nothing else, I can scrounge the "mirror module" out of the new unit and keep the rest for replacement parts.

I guess I'll call CDan back and order a new one.
 
Used epoxy on the drivers side over a year ago gooped it all over even on the unbroken areas, couple of elastics to hold it till dry, good to go.
Did the pass side last month.
 
Back
Top Bottom