Minor emergency

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 13, 2013
Threads
31
Messages
151
I was doing some of the off road trails in big bend and had a front sway bar bushing disintegrate, so the say bar is rattling like crazy. (Not surprising after 300k miles. I should have replaced the darn things any way)

The question is, do I ignore the rattle until I get home, make a bushing out of a shop rag, or do I just remove the front and rear bars permanently.

(97 lx with OME HD springs)
 
I ran with a blown front bushing for a couple thousand miles without much issue (aside from the annoying rattle). Shop towel may not be a terrible option, though.

Suppose it depends how far from home you are...
 
I ran with a blown front bushing for a couple thousand miles without much issue (aside from the annoying rattle). Shop towel may not be a terrible option, though.

Suppose it depends how far from home you are...
I have another day at big bend and then 300 miles home. I took the route of using a shop rag to make a bushing. We'll see how long it lasts. Thanks for the input.
 
Personally, I wouldn't worry too much at it with those distances.

If you are worried you could always just pull the front sway bar. Lots of people run without them 100 percent of the time. I'm not sure if the clattering without the bushing did my rig any harm but I've not seen any issues with it. Maybe it puts more strain on other bushing/linkages. Shrug.

Disclaimer: I take a slightly more relaxed approach to my truck then a lot of people here. I'm sure I'll catch some flack for saying it'll be fine, all I know is mine was.
 
Last year I stripped a shock stud on River road and blew my high pressure power steering line within 10 minutes. I drove to Napa in Alpine and got a new shock and line. It's about an hour away. But you will probably be fine with the rattle. I love big bend. One of my favorite places to go. The stars at night in the Chisos mountains are like nothing else.
 
Given the sway bar’s proximity to things like brake lines and ABS harnesses, if you’re still wheeling, I would consider taking it off. Those brackets can fail and without a bushing it’s going to move around against them more.
 
Remove it, you might like it better.
 
Put back on with the shop rags when driving home on the hwy. ...Safer.
 
My issue with removing the bar here is that I need to figure out how to mount the wires that are mounted to it.
If the shop rag gives out I'll move toward removing it.
Although, we aren't doing any real Wheeling tomorrow.
 
Update.... I drove Maverick road and side trails + maybe 100 road miles, and the rag bushing is still working.

With my 2 in lift, should I do something different with the mounts and endlinks? (Other than replace with OEM or equivalent)
 
Update.... I drove Maverick road and side trails + maybe 100 road miles, and the rag bushing is still working.

With my 2 in lift, should I do something different with the mounts and endlinks? (Other than replace with OEM or equivalent)

Do what I did. Order a set of disconnects from LCP and new bushings from Wits' End. They are easy to press in with a c clamp and the LCP disconnects are an amazing improvement to the suspension for next to nothing.

I also have a 2" ome lift and am not running drop brackets. I'm sure everyone has their own opinion.
 
Run it!
 
I like the "Run it!" comment. After another 550 miles on the drive home, I figure why not?

Thanks for the suggestions on quick disconnects and bushings. I'll look into those.
 
I'm more impressed that you have internet out there to post on Mud. Every time I've been out there I'm lucky if I can catch a 3G or Edge signal for long enough to fire off a text message, those cell signals are floating around out there like a fart on the wind.
 
I cheated... I had wifi at the Airbnb I was stayin at.
internet access in the park was very rare. I didn't even try.
 
I just realized something...
The bushing kit and the LCP sway bar disconnects won't completely solve my problem. Part of the reason the bushing failed was that grease from the "downlink"(?) that attaches to the frame leaked out all over the bushing and finally rotted it away. (minor oil leaks over many years did most of the damage), but when I put the rag in their for a bushing, there was grease everywhere. Do I just replace those with OEM?
 
I took mine off and never looked back
 
Enough people have suggested removing it, that I guess I should give that a try.... I just need to figure out what to do with the wiring that is attached to the anti-roll bar. (not to mention, this is the easier solution :)
 
I took mine off (with a little help from the Poison Spider trail in Moab) and it's been off for over a year now. Brosky was there, a little disenchanting when the spot weld failure takes out a brake line on a steep downhill portion
 
The wires are for the front locker. This is what I did with mine. made this bracket
F350440D-9D40-408A-9221-1E9E94B59192.webp
53FA8978-F816-4020-A1E6-DBC05A65E54D.webp
 
Back
Top Bottom