master cylinder problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 1, 2005
Threads
15
Messages
67
Location
arcata calif
hey hows it going i own a 71 fj 40 im restoring . i found the truck in a field with sticker bushes groing thruogh it. enyway the breaks were really bad on the rig so i checked the shoes and they seem to be ok its the master cylinder thats shot i would be driving down a hill and all the sudden no breaks. so i put the new master in and took it for a long ride i stoped about 15 miles out of town to get gas and when i get back in to take off the truck seems to be draging i mean i can get it past 40 mph so i pull over and every thing seems to be working right so we keep on going then we start smelling breaks we pull over and notice the back drivers side breaks are smoking so i wait till the thing cools of and go back into town later that day i tryd to get them to lock up but nothing till now when i came home yesterday the breaks were beging to lock up. i dont know what to do can i adjust my break drums to fix the problem or is the new master cylinder falty or do i have a bad break booster . i dont know how to fix it please help. thanxs
 
should i have bleed it weel by weel?



Yes.

Start with the wheel furthest from the master cylinder in the front and then rear circuit.


Your year vehicle should have bleeders on each wheel cylinder, make sure you bleed them all, the same way as specified above, starting with the cylinder bleeder valve furthest in the circuit.



Good luck!


-Steve
 
not much help

This may or may not help you or me, but i have a question along these lines.

I have 78 FJ 40, just replaced the front and rear brakes, also replaced the wheel cylinders on each side in the rear. I have bled the breaks over and over again and the brake pedal continues to be mushy with virtually no breaks. I replace the drivers side wheel cylinder first, once this was done the driver side would lock up completely and the passenger side would spin freely. i then replaced the wheel cylinders on the passenger side and it seemed like everything was ok.

After all of this i still do not have breaks, i can brake, it is very slight and doesnt seem to build any pressure in brake pedal.

Any suggestions?
 
This may or may not help you or me, but i have a question along these lines.

I have 78 FJ 40, just replaced the front and rear brakes, also replaced the wheel cylinders on each side in the rear. I have bled the breaks over and over again and the brake pedal continues to be mushy with virtually no breaks. I replace the drivers side wheel cylinder first, once this was done the driver side would lock up completely and the passenger side would spin freely. i then replaced the wheel cylinders on the passenger side and it seemed like everything was ok.

After all of this i still do not have breaks, i can brake, it is very slight and doesnt seem to build any pressure in brake pedal.

Any suggestions?



Adjust your rear brakes....
 
I replaced my master cylinder recently, was pulling my hair out when 5 nights latter i still had virtually no brakes. Long story short, adjusting your breaks then bleeding them works so much better, else you never seem to fully get all the air out! I could actually hear the springs moving on one of my drums where the shoe was so far out of adjustment it was taking a lot of fluid to move it. Make sure you re-adjust your shoes a few times so they bed in properly... you'll see what i mean!
 
I replace the entire brake system on my truck, master, hardlines (with new SS) soft lines with SS, calipers, rotors wheel cylinders and you name it.

It took a long time to get all of the air out, I couldn't get pedal until I finally adjusted the back brakes. I adjusted each rear cylinder until I felt drag them backed it off and had my father push in the pedal and seat the shoe. I adjusted each shoe with this method, drag, seat it then back it off on or two clicks. Finally I got them all close and advanced the cylinders to slight drag. I disc brakes up front so they were easy.

BUY SPEED BLEEDERS for your truck! I bought a pressure bleeder and it was a waste of money. I never do that one again, it may have helped but I'm going to try and learn how to gravity bleed before I ever do this again.-Junk
 
well its been two days since i bleed the break drums weel by weel and my breaks havent locked up i just bleed each cylinder like the way described above and it worked all the air is out . the break peddle ust to be hard and it didnt travel its full distance after i bleed the system the peddle feels good travles the full distance and feels solid thanks again steve for the advice i have never had breaks im my truck as good as they are now thanks and thanks to everyone who added to this thred . -matt
 
well its been two days since i bleed the break drums weel by weel and my breaks havent locked up i just bleed each cylinder like the way described above and it worked all the air is out . the break peddle ust to be hard and it didnt travel its full distance after i bleed the system the peddle feels good travles the full distance and feels solid thanks again steve for the advice i have never had breaks im my truck as good as they are now thanks and thanks to everyone who added to this thred . -matt




Have you adjusted the brake shoes/wheel cylinders?



How much pedal travel do you have before the pedal gets firm?
 
now i have the saim problem but the peddle is stuck down i called man-a-free asked them what they thought .there sending a new master out to replace the falty one ill let you know how it works out right now i have my fj60 down and my fj40 down i love cruisers
 
ok yesterday i got the new master cylinder in the mail exchanged it and sent back the falty one. when i put the new one on i also checked my break shoes and adjusted the amount of drag on each cyilender to whare its just right.put my wheels on put fluid in then i bench bleed the master cylinder before i put the hard lines on witch made a big diffrence. then attached the hard lines into the new master cylinder and everything went good. the peddle has good travel and im getting pressure pushing the peddle back so far so good. today got home from work and every thing is good. i think its fixed :rolleyes: . i want to thank you all for your help . p.s anybody know whare the main ground for the fuse box is. i keep blowing my headlight fuse.
thaxs matt
 
ok now im stumped driving home today i got my peddle stuck in the down position and it dosent come back up i dont know what the heck to do. when i got home the breaks were rubbing and you can smell breaks the peddle was stuck down and i had no breaks i know for fact that i bled all the air out of the system. and can you explane to me if there is air in the lines how would that make my peddle not come back up wouldnt it make the peddle soft. could it be the break booster could there be somthing stuck in the lines. i know that the pistons on the break drums are in good condition could it be the springs for the drums are messd up.
i got the conversion kit for disc breaks all aroud i was waiting till i can aford the hard lines to be put it on but even if i put the hard lines on ill still have the saim problem im stumped:confused:
 
Sounds like you may have a leak somewhere. You have to remove the drums and inspect the wheel cylinders. Also check your calipers and start over bleeding the master cylinder. You can either replace the wheel cylinders at a you local auto part store.....may even come with a lifetime warrenty. Or rebuild them if you can locate the seals. Good Luck.
 
ok i got the answer to my problem and also for everbody else thats having the saim probem i went to rockys 4x4s off road shop and told him what the was happening and he knew what to do right off the bat he smiled and told me that the master i got is just a little diffrent and the adjusting bolt that runs from the peddle through the break booster needs to be adjusted so the master has room to dissengage and depressurize the pistons so the shoes can reseed. the reson it wasnt happening all the time was becouse i didnt use the breaks full foce all the time .once i did my peddle would be stuck down.when he told me this it all made sense it was like the mecanicle guru teaching the puple awsome. i went home and did what he told me bled the breaks and it seems to be all fixed so if your having trouble with your master cylinder try adjusting your rely bolt that runs thruough the break booster
good luck
 
Back
Top Bottom