Making a 6cyl a 4cyl ?????

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 5, 2008
Threads
27
Messages
264
Location
FT Lewis WA
The cutout switch sounds bogus. Nice truck, low mileage, lockers. Street wheels & tires and rear drum brakes with SF axle. Highest bid when I checked was $2424. Interesting to see how much it goes for.
Edit: The bottom left pic (of wheel & tire) can't see caliper or disk through wheel, maybe does have 4x disks and FF. Hard to tell.
 
Last edited:
Looks to me like he has taken good care of the truck but his claim that "switches" will reduce fuel economy seems a little bit far fetched. Need more information to know for certian. Hard to swallow though.
 
You might be able to take out 3 cylinders w/o severe imbalance but 2 would not make sense. The engine has three pairs of cylinders. When one is at top dead center on the combustion stroke another is at top dead center on the exhaust stroke. How could someone just change 2 cylinders? The real issue I would see is how he then fools the computer to give the correct A/F ratio. The unused cylinders are still sucking air through the system - metered air that affects the A/F ratio.

This is not mechanic territory - but automotive engineer territory. No way no how - sorry not true.
 
If you just shut off the injectors for the cylinders you don't want to use, that will idle those cylinders. They will still consume the same amount of air as before, just not the fuel. Thus your air/fuel ratio will be unchanged for the remaining running cylinders.

I see one of the issues being, how do you prevent the ECU from detecting the misfires and throwing a code? Which may then cause the ECU to go into "limp home" mode which to my limited knowledge causes rich fuel mixtures and retarded ignition timing. Thus increasing fuel usage in the remaining four cylinders and further degrading performance of those cylinders.

I think it is doable, just not practical. Unless every where you go is downhill. ;)
-jim
 
If you just shut off the injectors for the cylinders you don't want to use, that will idle those cylinders. They will still consume the same amount of air as before, just not the fuel. Thus your air/fuel ratio will be unchanged for the remaining running cylinders.

I see one of the issues being, how do you prevent the ECU from detecting the misfires and throwing a code? Which may then cause the ECU to go into "limp home" mode which to my limited knowledge causes rich fuel mixtures and retarded ignition timing. Thus increasing fuel usage in the remaining four cylinders and further degrading performance of those cylinders.

I think it is doable, just not practical. Unless every where you go is downhill. ;)
-jim

Good point. I still say 4 out of 6 is all wrong with the geometry of the crankshaft. Mine was running on 5 once - not fun at all. The engine shaked like it wanted to get out.

Caveat emptor - Wikipedia, the free encyclopedia
 
The cutout switch sounds bogus. Nice truck, low mileage, lockers. Street wheels & tires and rear drum brakes with SF axle. Highest bid when I checked was $2424. Interesting to see how much it goes for.
Edit: The bottom left pic (of wheel & tire) can't see caliper or disk through wheel, maybe does have 4x disks and FF. Hard to tell.

It would have to be a FF to have lockers. :cheers:
 
It would have to be a FF to have lockers. :cheers:


OK, thanks, Chad! Wasn't sure since I don't have lockers. Was zooming through pics and when I got to that bottom left 1, I didn't see rotor or caliper through wheel and an alarm went off in my head:rolleyes:. Can't see the hub 'cause of the center caps, so after the cutout switch brag, it looked fishy. Must be the angle or maybe trick photography?:D
 
what Schmeal said. :rolleyes: not worth your time or effort IMHO.
 
. . . The real issue I would see is how he then fools the computer to give the correct A/F ratio. The unused cylinders are still sucking air through the system - metered air that affects the A/F ratio.

This is not mechanic territory - but automotive engineer territory. No way no how - sorry not true.

If you just shut off the injectors for the cylinders you don't want to use, that will idle those cylinders. They will still consume the same amount of air as before, just not the fuel. Thus your air/fuel ratio will be unchanged for the remaining running cylinders.
. . .

You might be able to fool the ECU to make the engine deliver the correct exhaust oxygen to the O2 sensors -- but there's no way that engine can be fooled into delivering the correct A/F ratio to the cylinders, where it counts.
 
where can I get a "magic switch" !?

The guys been partying too much with Micheal Phelps......:rolleyes:
 
where can I get a "magic switch" !?

The guys been partying too much with Micheal Phelps......:rolleyes:

My thoughts exactly. If shutting down cylinders to save fuel was doable, Wouldnt everyone be doing it. And I dont trust the mileage either mine looks better and it has 139k miles.
 
What a waste of time. None of us here on MUD drive these trucks for the great fuel ecomomy. Here's a great fuel saving tip- if you can't afford the gas- don't drive an 80 or at least drive it less. Don't screw with the 1FZFE in such a way. The whole premise sounds bogus to me. (at least with an 80).

BTW- I wish my 80's engine ran "with turbo like power" :doh:

Pete
 
Besides A/F ratio I think that ideally you'd need to leave the valves open or parially open, at least on the compression stroke. Otherwise the "dead" cylinders would have pumping loses as they are still going to take in a volume of air and compress that air against closed valves. No fuel, no spark == no power but they're still doing work...
 
Back
Top Bottom