Locker question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 17, 2015
Threads
20
Messages
115
I've gone through most of previous threads about the lockers. So my rear engages with no issues, however, front locker sounds like it's engaging. I turned the car to on position with out the engine on I put it on 4Low and turned on the rear and I heard the noise I'm supposed to hear. Now again I have no issues with the rear. I turn the locker dial one more to the right (to front locker position and I hear the actuator motor working and the lights blinking. I turn them on and off front and rear multiple times then I decided to leave the front and rear on locked position. I removed the actuator and I turn it to lock and unlock and I see the gear spinning back and forth as I turn the dial to on and off. When I removed the actuator I saw the fork gear inside the hole and seeing the other threads I tried to move it and it moves maybe half and inch or less back and forth. But judging by the pictures of the fork it's supposed to be on the left side and mine is all the way to the right meaning my right side of the fork is all the way to the right side of the hole. Sorry for the locker thread again but I need some answer or clarification if I'm doing something wrong.
 
It is possible the shaft or actuator has been assembled in the wrong position by a previous repair?

When trying to move the fork manually make sure you have both front wheels off the floor and are rocking them back and forth while putting pressure on the fork.

Regards

Dave
 
It is possible the shaft or actuator has been assembled in the wrong position by a previous repair?

When trying to move the fork manually make sure you have both front wheels off the floor and are rocking them back and forth while putting pressure on the fork.

Regards

Dave

Thanks Dave. I'll post some pictures on this thread tomorrow ... I did read somewhere on the forums that the front has to be off the ground and the tires need to be rocked back and forth. I didn't try it off the ground. I'll try it and see how it goes

Joe
 
Thanks Dave. I'll post some pictures on this thread tomorrow ... I did read somewhere on the forums that the front has to be off the ground and the tires need to be rocked back and forth. I didn't try it off the ground. I'll try it and see how it goes

Joe

You only need 1 tire lifted (save you going full jackstands) - when locked the 1 lifted wheel won't spin, open/unlocked it'll keep rotating.

The design of the front vs the rear lets the FR engage quicker than the rear, and when locked the indicators in your dash cluster go from blinking(pending engagement) to steady(locker pos sensor reading as locked diff)

Added that as the rear sensor I've had bad luck with, replaced 3 between 2 e-lock 80's - so in perfect condition, cluster indicators blink when pending lockup, glow steady when locked position.
 
It is possible the shaft or actuator has been assembled in the wrong position by a previous repair?

When trying to move the fork manually make sure you have both front wheels off the floor and are rocking them back and forth while putting pressure on the fork.

Regards

Dave

You only need 1 tire lifted (save you going full jackstands) - when locked the 1 lifted wheel won't spin, open/unlocked it'll keep rotating.

The design of the front vs the rear lets the FR engage quicker than the rear, and when locked the indicators in your dash cluster go from blinking(pending engagement) to steady(locker pos sensor reading as locked diff)

Added that as the rear sensor I've had bad luck with, replaced 3 between 2 e-lock 80's - so in perfect condition, cluster indicators blink when pending lockup, glow steady when locked position.

Thanks to you both I got it fixed. So when I pulled out the actuator I noticed the fork was all the way to the right. Got a jack and jack stand and lifted one side of the front. Rotate tire and the fork was easily pushed to its locked position with the actuator in locked position as well. Installed everything back together. And tested. Finally have front lockers again. Didn't have time to actually look into it or I was hesitant about it. But appreciate the help fellow mud members.:beer:
 
When you reinstall the actuator, the fork should be in the locked position. There's no way the fork gets misaligned through use unless something is FUBAR.

If it's working now, sounds like PO put it together wrong.
 
Back
Top Bottom