lined my 80 again

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 1, 2005
Threads
5
Messages
95
Location
Camp Verde Az
After 2.5 years with Herculiner on the truck (which shrinks and fades over time leaving exposed paint/ bare metal) I decided I would redo my bed liner. I used a grinder with a wire cup to remove all the old bed liner in about 30 hours worth of work. I do not have pictures of the prepped surface but I went to metal. I stripped the truck of all its side molding, front fenders, hood and grill. I did not feel like taking the doors apart to get the handle off so that I masked. I purchased 2 gallons of Durabak-18 the uv protected stuff in black. I rolled it on today with help from a buddy, 2 gallons was just enough to get this done. hopefully this product lasts a little better. Thanks to all you mudders for the inspiration and for the information about different products. :flipoff2:
Photo_110108_001.webp
Photo_110108_006.webp
Photo_110108_002.webp
 
Almost forgot I used JB Stick weld to fill all my holes then ground it somewhat smooth.
pic one is from a while back the bedliner still looks ok
pic two if you look just under the windshield you can see the bedliner has shrunk and exposed the paint underneath I have seen this on two other trucks in places that the herculiner was rolled on thick
Photo_042508_007.webp
Photo_020908_001.webp
 
I'm interested to hear if anyone else has had this problem, it's on my list of things to do. Did you apply the original liner or did you have it done?
 
I applied the liner myself, sanded with 60 grit cleaned with xylol and rolled.
just finishing putting the truck back together will have completed pics tomorrow.
 
finish off the rest of the truck make it an "avocado" #2 of course

I did the inside of my rig with Herc. and it has not kept up with the abuse (it is also VERY rough, more hard plastic than rubbery). I did 3 coatsl with proper prep before and dry time after. It's been two years and it looks like crap. I will do a pro bedliner spray if and when I do it again.
 
I also didn't like how rough the herculiner was. the Durabak has much more evenly sized chunks. now that the stuff has cured a bit... it is definitely more smooth. I am very pleased with the results so far...
pic one is a close up of the offending liner
pic two is my grill
Photo_110108_007.webp
Photo_110108_008.webp
 
I also didn't like how rough the herculiner was. the Durabak has much more evenly sized chunks. now that the stuff has cured a bit... it is definitely more smooth. I am very pleased with the results so far...


I wanted something MUCH smoother than either of those for mine. The Duplicolor is a very smooth finish bedliner, no chunks at all.
 
man that looks great i just did the inside of a 88 sas yota truck and i want to do the bottom edege of the truck did you use theroller that comes in the kit ??????????
 
I did my flares and bottom section of my truck about a year ago. Some sections of my flares look like the picture above your grille, like it wore off. I have heard people spray with black rattlecan and it looks better. I used Hurculiner on my truck. I rolled it on and did 1 thin coat first, 1 thick coat later in the day, and 1 thick coat the next day.
 
Last edited:
more pics

Baja Dan: thank you and I did use the roller that comes with the Durabak (blue foam)

Sno bored: Did you use durabak or another product?

I rattle canned all the headlight/turn signal trim pieces black today. overall I am pleased with the way it turned out. I have a few drips on the doors that I am not concerned about. the truck has been turning heads all day.:steer:
Photo_110208_002.webp
Photo_110208_004.webp
Photo_110208_011.webp
 
more

a couple more

Edit: I did not line the entire door so I don't end up with a raw arm
Photo_110208_012.webp
Photo_110208_001.webp
 
Thanks, and did you remove the front sides, hood, doors, and back sides to paint? and if so how many coats did you do and how long to dry and (Last Q) did you detach hood and sides? (Bolts?)
 
motoloco: thanks :flipoff2:


raymanrockz: post one pic three shows what I took off... I did two coats... its just a bunch of bolts
 
I just skimmed through the responses, so I might've missed a post, but why did you go down to metal? why not simply apply over the old stuff -- sure, clean it up a bit, but apply right over the top.

sure, going down to bare metal probably gives the best results and there'd be no visible "panty lines", but 30 hours seems to be a lot of time at the grinder/sander to me...


were you concerned about additional shrinkage from the herculiner?


just curious.



looks nice, btw. :cheers:
 
Let me preface my post with this: to each his own.


This is why I am afraid to line my truck. It looks like sh*t. I am glad you like it, and I am sure it suits your needs. Maybe its just be the contrast of the black against the silver, because Beno's truck isn't as appalling.
 
NorCalDoug: thank you... I went to metal because I wanted to do it the right way this time and a areas that the herc was peeling (rockers/inner fender lip). the new liner would only have as good of adhesion as the old... however I found more bondo on my truck than I wish to express :bang: ... this body is perfect for liner and abuse

Ruadhrigh: I thought about trying to color match and do the desert sage whatever it is, but I figured it wouldnt look correct and how hard is it to mess up black... as far as suiting my needs it does very well I dont worry about pin striping I dont spend hours waxing to make the paint look decent, the big down side is cleaning mud off the truck.... believe me with all the body damage this truck suffered with the last 2 PO's this thing looks beautiful...
 
I lined a small TEQ blister in on each front door.
Photo_110308_001.webp
Photo_110308_002.webp
 
Back
Top Bottom