Leakdown test and valves

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 18, 2005
Threads
30
Messages
326
Location
Central Florida
Is there a trick to closing valves to run leakdown test? ...other than having to remove valve cover to observe. The #1 cylinder is closed at TDC and #6 after rotating crank one revolution but not sure how to get the others.

thanks for any insight, ChuckD

:beer:
 
That's the trick, how much do you rotate crank to get the next cyl to shut all valves. I was hoping there is a "method", ie, turn crank 1/2 rotation, etc.

Thanks for the reply. ChuckD :beer:
 
well, if the piston moves with the 100 psi, presumably you can't do a leakdown test at 100psi, as suggested by the HF manual it seemed. Do you use a lower pressure?
 
I was going to do this while the valve cover was off to see the cam lobes but thought that may interfere with one of the tests, ie, air coming from the throttle body or something.
Good point about the pressurized cylinder. Any other ideas out there?

ChuckD
 


why what? How can you do a meaningful leak down test if the piston is moving?

anyway, if the piston is at true TDC, why would it go down since presumably the rod is fully aligned with the stroke axis?
 
I was going to do this while the valve cover was off to see the cam lobes but thought that may interfere with one of the tests, ie, air coming from the throttle body or something.
Good point about the pressurized cylinder. Any other ideas out there?

ChuckD

It would be a good idea to verify the valves are closed but if the rings are leaking you now have a huge hole in the crankcase. If you start with #1 at TDC on the compression stroke and work your way through the firing order all you'll have to do is pull the next plug and while pulling the engine through look down the spark plug tube into the combustion chamber.

The test can be done at any pressure (within reason) as long as the piston is on TDC. If the con rod is vertical the piston had better not move. If you can't be sure your at TDC just reinstall the other five spark plugs and it should help keep rotation to a minimum. For aircraft engines the standard is 80psi with an minimum acceptable leak rate of 60/80. We won't delve into the Continental (TCM) acceptable figures because it's a can of worms and a separate thread all together. Here is a good article to familiarize yourselves with and may answer some questions you may have.

Compression testing
 
why what? How can you do a meaningful leak down test if the piston is moving?

once the piston hits BDC (bottom dead center) it stops moving. From pressurizing cylinders for seal replacement that takes about 2 seconds.

But if you are hell bent on TDC mark the positions of the wires around the base of the dizzy and then pull the dizzy cap and point the rotor to the mark that coresponds to the cylinder your testing.
 
So maybe it's as simple as pressurizing the cylinder and when it bottoms out then the valves are all closed...? Then keep on down the head doing each cyl. Or do the dizzy trick. (it didn't occur to me that when the dizzy points at a cyl it's go-time and the valves need to be shut to capture the boom).

Thanks for the advice.

ChuckD
 
Do not perform the test with the piston at BDC as it will not portray an accurate indication of the cylinder/rings condition. The highest combustion pressure the engine sees is at or near TDC on the power stroke which is where the vast majority of cylinder wear occurs. Have you seen or used a cylinder ridge reamer on an old Ford or Chevy? Since the greatest wear occurs in the top 1/4 - 1/3 of the cylinder the ring gap will also be at its greatest.

I didn't see any info stating how many miles you have on your rig but I just had my top-end apart and at 210k there is zero ridge and the original hone pattern is still clearly visible. Now that's not to say the rings are in perfect shape but overall it looks promising for a long service life.
 
Back
Top Bottom