Knocking valves rough idle

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 11, 2007
Threads
2
Messages
8
Location
Florida
Hello

My name is mike, and this is my first post. I own a 1992 fj80 with 145000 miles.
My fj80's history- I bought this truck 1 1/2 years ago as a big fixer upper project. The previous owner really abused this truck. :bang:
I have rebuilt the engine. had the block and the head sent off to a machine shop. the block was shaved and bored to .20 and all new parts installed . the head on the other hand was shaved and checked for cracks and returned clean.
Now for the problem, fj80 is running very rough, missing, and has a knocking noise sounds like a sticky valve or something along those lines:confused:. I also noticed two of my spark plugs are wet smells like fuel 4th and 5th cylinder area. I have white smoke coming from the tail pipe.
Please advise :bang:
 
"The previous owner really abused this truck."

What does this mean?

"I have rebuilt the engine."

Why?

"fj80 is running very rough, missing, and has a knocking noise sounds like a sticky valve or something along those lines"

Sinice you did the rebuild? Fine after rebuild and then went down hill?

Without real details I would say you did something wrong. Do you have a FSM? Did you use all OEM parts?
 
I would check the timing chain too (wait, does the 3f use gears?), sounds like the either the chain/gear is off a tooth or two or the distributer is off.
 
All the plugs are firing. new fuel injectors, filter,fuel pump, main relay is also new.

I have the FSM.

"The previous owner really abused this truck."
What does this mean?

He overheated the engine and tried to have the problem fixed, but never figured out the problem. looks like he preformed no PM.

"I have rebuilt the engine."

Why?
After, I had the machine shop look at the block he said the head gasket was blown and water sitting in the cylinder for some time .

Sinice you did the rebuild? Fine after rebuild and then went down hill?
It was fine after the rebuild ran very strong then one day it stopped in the parking lot of grocery store wouldn't start. I couldn't hear the normal sound of the fuel pump running . I waited 15 min. and it started back up. It did it again 10 min. later going down the road, after finally getting it home I ordered and replaced the fuel pump non OEM not the problem! I then replaced the main relay and bingo fixed.
 
It seemed to run well, but had problems accelerating over 40 mikes per hour after a few miles it started running hot so I stopped and found the throttle control connector not hocked up to the switch,
after connecting the switch it stopped running hot, but seemed to run rough, knock, and white smoke.
 
OK, so to recap...

Successful motor rebuild due to overheating yielding a decent motor, followed by EFI relay failure, followed by overheating, followed by poor running.

You say the "throttle control connector not hocked up to the switch" caused overheating. What connector are you referring to? The throttle position sensor? Idle speed control sensor? I can't imagine that this would have any bearing on overheating. Sounds like you need to go back under the hood and look for other connectors or vacuum lines that are not in the right place. Any codes being thrown by the ECU?

After the rebuild did you address the cooling system? I'll ask this again...did you use OEM part for the rebuild?
 
it was the throttle position sensor that was not connected when the truck ran hot.

OEM part for the rebuild?
I used high quality parts that meet Or Exceeded OEM specifications.

The cooling system was addressed, new water pump,radiator, all hoses brand new, new thermostat, system has been drained and flushed with water 3x's.
 
Repost, give us a time line and tell us EVERYTHING.... It's hard to help without knowing the facts, start just before the rebuild and include the reason for the rebuild.
Did it run?
How well?
How long?
What were you doing when the problem started?
what were the conditions?
have you checked the timing?
have you pressure tested the cooling system?
have you checked the condition of the plugs?
have you done a compression check?
Are all the plug wires routed correctly?
do you have any major vacuum leaks?


that will be a good start.
Try to put all this together with the timeline in one post.
 
Please Help

How can we help you if you don't answer the questions?

So far your timeline of events makes no sense to me. You say after the rebuild it was all groovey. Then an EFI relay failure caused connectors to fall off and the motor to overheat.

C'mon man. Give us something to work with here.
 
Back
Top Bottom