Key/Ignition Issue- 1992 80

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 28, 2016
Threads
84
Messages
872
Location
Indiana
I have done some homework on my issue and I cant seem to find one response to my specific problem. So I’m posting a question.

I noticed earlier in the week that when I shut down the truck it acted funny and didnt seem to like going into the lock position so I could remove the key. It did go. Today I went to shut it down and it just stayed in the ACC position and wouldnt go to lock. So after a review of the issue here on Mud I wiggled the key, moved the shifter forward, spun the wheel.... None of the fixes I read up on seemed to do anything. I lubricated the barrel as well. So I disconnected the battery and went home.

I have a new key that was cut at the dealership with the VIN on an OEM key.

I know there is a device under the shifter console and a solenoid behind the barrel. Could one of those be my issue? I dont know how to diagnose this.

Any help is appreciated.
 
Last edited:
If you mean that you can't remove the key from the ignition lock, you're problem is likely the lock itself. There's a small babbitt plug at the bottom of the lock. It sits on a small spring and has to be depressed in order to release the cylinder lock. Over time, it gets a dimple in the end, because it's soft. The result is that your key is now too short to reach the pin.

If this is the problem, you have two choices, replace the lock (I wouldn't) or have a new key made. Tell the dealership what your problem is and ask them to move the key blank forward in the clamp. It doesn't take much, only a few thousandths of an inch. This will result in a longer key, which will push the pin in.

It's unlikely that the shifter lock solenoid is the problem, as it gets a signal from the ignition lock, not the other way around. As far as I can remember, the steering wheel lock solenoid is separate from the ignition lock solenoid in the same way.
 
There is a shift lock ECU module under the center console. It controls the shift lock solenoid and the key interlock solenoid.
The schematic and description is found on page 86 of the factory EWD.
Thanks Jon. I read up in a non Land Cruiser Repair where they cleaned up the solenoid. TJ
 
I had problems with my key and ignition in my '92. I went to the Toyota dealership and had a new key cut using the code for the VIN, and the problem went away.
I did that about 6ko this ago. But thanks.
 
If you mean that you can't remove the key from the ignition lock, you're problem is likely the lock itself. There's a small babbitt plug at the bottom of the lock. It sits on a small spring and has to be depressed in order to release the cylinder lock. Over time, it gets a dimple in the end, because it's soft. The result is that your key is now too short to reach the pin.

If this is the problem, you have two choices, replace the lock (I wouldn't) or have a new key made. Tell the dealership what your problem is and ask them to move the key blank forward in the clamp. It doesn't take much, only a few thousandths of an inch. This will result in a longer key, which will push the pin in.

It's unlikely that the shifter lock solenoid is the problem, as it gets a signal from the ignition lock, not the other way around. As far as I can remember, the steering wheel lock solenoid is separate from the ignition lock solenoid in the same way.
Thanks for input. I think it’s a solenoid. The key will come out if I could just get it to the Lock location in the barrel.
 
There is a shift lock ECU module under the center console. It controls the shift lock solenoid and the key interlock solenoid.
The schematic and description is found on page 86 of the factory EWD.
So after disconnecting the battery last night I hooked it all back up and the key came right out. I fired the truck back up, let it run for a minute and then shut it off. Same thing again. Key wouldn't go over to the lock position. I assume theres a capacitor somewhere that completely drains when the battery is off. Is that inside the ECU module?
 
Back
Top Bottom