JT Front disc conversion??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 18, 2005
Threads
2
Messages
9
Location
Lehi, UT
Has anyone here installed the JT Outfitters front disc conversion for an fj40? I have some mini-truck parts but the JT kit seems pretty easy and cheap considering that fact that I don't have a complete set of mini-truck parts. I only have one hub and no knuckle arms, calipers or rotors. Any opinion on front disc conversion would be nice.
 
IMO, the best value for the dollar/effort is the minitruck conversion...heck, I swapped my 77 disc front over to the minitruck knuckles and lockouts for the added strength.

Does the JTO replace the birfields? if not, don't bother....
 
just read up on it....

you get disc brakes, using GM Monte Carlo calipers...

you DO NOT get: stronger birfields, stronger knuckles, stronger lockouts, Toyota calipers, stronger steering arms, the opportunity for MANY more hi-steer options, etc...

You get the powder coated backing plates, vented rotors, loaded calipers, new hoses, and all the hardware. - $549.95

rotors will be from a GM application, $30 each plus a little machining...calipers are $20 each, loaded w/ hardware...hoses will be $15 ea....$150 plus a pair of $400 brackets....

IMO, of course.....
 
if you leave your front axle unlocked, coarse birfs may last....may....

I busted quite a few fine spline birfs and early Newfields with 33" tires....locked front axle tho, and I tend to drive "harder" than most.....

IMO, the mini conversion can be done for around $300-350 with some patience....and you end up with a better end product.
 
well IMO , my coarse brif's on 36's and a sbc , 420 have lasted thru o.k. , did break one on old sluice but the same situation woulda broke a mini birf too. Put the JT kit on and if you start breakin get a 60/LC hybrid. :)
 
What knuckle arms would you recommend? I've got 70 fj40 and mini truck. Do I need to buy '81 fj40s (~$130 each)? If not, what's your recommendation?
Thanks for your opinions.
sorry if i'm being a pest
 
just converted my front end to disc with the minitruck stuff, $350 for the complete axle at a wrecking yard, and they gave me $150 back when I returned the housing third member and inner axles. You can use the minitruck steering arms then too. Not too hard to convert to vented 60 rotors and IFS calipers later. IMO it was the most cost effective was to go.
 
You can get shims to fit in the minitruck knuckle arms so the cruiser TRE's will work.

You could also use a minitruck tie rod. (not as strong as cruiser)

Could also make a minitruck TRE/custom tierod

Could do what I did and buy 79+ cruiser knuckles for $225. Same everything as minitruck, with arms that fit cruiser TRE's, and vented rotors.
 
I've got the JT disk conversion on the front of my HJ-45. I am not planning on wheeling this truck much. It wears skinny 33's and will be used for some hunting excursion and the like. I have my 42 for the hardcore stuff. I like the conversion just fine. I have had no issues with proportioning, etc. It stops and stops well. I bow to woody's superior knowledge in all things; however, if it's not gonna be wheeled hard (or at all), it's not gonna fail ya.
 
I have seen several mentions of 60 Vented discs. My 78 Discs are vented??? Are they not on the earlier models?
 
cut and welded

The thing that bothers me the most is " off road use only" and these things are sold like crazy.

who is liable?
 
Back
Top Bottom