Intermitten vibration

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 14, 2007
Threads
7
Messages
35
Location
Utah
I have a 1996 LX 450 with lockers. While driving yesterday and today I have been getting and occasional vibration. The vibration feels and sounds like I am driving on the rumble strips on the freeway. It has happened at high speeds, low speeds, accelerating, braking, coasting, it doesn't really seem to matter on driving condition. Today I had the brake shop take a look but they could not find anything wrong. I have done several searches but I have come up empty. Anyone have experience with these symptoms?
 
I would look hard at the u-joints. have they been greased at normal intervals? the snow and salt in your area can do a number on neglected joints.

Yep, the ujoints have been checked over and over because that was my initial thought. It is very intermittent. It lasts for about 5 seconds and sounds like your on the rumble strips and then goes away. It could be 200 miles before you hear and feel it again. Is this a viscous coupler issue?
 
I had something similar with cogged belts that were missing teeth.

Do you have cogged belts?
 
I had something similar with cogged belts that were missing teeth.

Do you have cogged belts?

I checked the belts, they are good, I am thinking it is the abs sensor on the drivers side.
 
Have you rebuilt the front axle lately?
 
What OME combo are you running?

I have been running the 2" OME HD lift for about a year. I had Kurt at Cruiser Outfitters install the lift and we had the caster correction done.
 
Have you rebuilt the front axle lately?

I had the front axle rebuilt 20K miles ago by a shop that specializes in rebuilding toyota front axles. I have also had all the brakes redone in the last 5K miles but I am starting to think that I may have dirty ABS sensors. I am pretty good with preventive maintainance, actually I am anal about it.
 
i would rather check the frt hub for ware & tear, they usually wear out quick, all you have to do is pop out the shaft cover & jack up one frt wheel & rock back & forth to c any much clearance on the drive shaft spline to hub clearance? i have been working on these 4x4 over 30 year of experience.
 
i would rather check the frt hub for ware & tear, they usually wear out quick, all you have to do is pop out the shaft cover & jack up one frt wheel & rock back & forth to c any much clearance on the drive shaft spline to hub clearance? i have been working on these 4x4 over 30 year of experience.

Already checked the front hubs, but they look great.
 
Well I got off the phone with Kevin Laboa at Six States Distributors in Orem, UT, and he thinks it the spindle bushings. He said he has built a tool which allows him to grease the spindles with out having to tear the axle appart. So I guess I will give it a try. I will let yall know if it works.
 
for what it's worth, i had an almost identical shudder that i (think) i've finally cured after a good bit of chasing. i went from new u-joints/balancing the DS, to new spindle bushings, new wheel bearings, new tires, and replacing all of the suspension bushings. my shudder/vibration improved after replacing the spindle bushings, but it didn't go away.
mine seem to have gone away after i got new OEM rotors and pads.
greasing the spindle bushing is an easy/cheap thing to start with and sounds like a good idea to me. in my case, i don't think any amount of lube would've saved my spindle bushings. they were pretty worn (they had over 200k on 'em)
 
I had what sounds like the exact same issues with my 94. I ended up rebuilding the front axel. My spindles looked completely dry and worn. I replaced them and made sure they were greased up well when I put everything back together. The vibes haven't come back since. I'm guessing it's your spindle bushings.
 
Yeah I hope getting the spindles lubed fixes it cause I have had everything redone on the frontend over the past 8 months which includes an axle rebuild, new brakes and rotors, cleaned ABS sensors, new tires, new suspension etc, etc. I only started shuddering yesterday so it could be dry spindles. I have put on 26K miles since I had the axle rebuilt earlier this year. This seems like the only logical thing that it could be.
 
Well I took my 450 in to have the spindles greased and as we were pulling the cap off the axle shaft we noticed that the c-clip was not attatched. The place that did the brakes last month fail to attach the c-clip which was causing my rattle and grease was slipping out the axles splines. We did go ahead and regrease the spindles which took all of 20 minutes. All is well and I have not had any issues for the last few days.:D
 
Intermittent Vibration

I just had the exact same noise in my '96 LC. My left side spindle bushing was dry and had some scoring. Replaced both spindle bushings and did the birf repack with seals and trunion bearings. Your description of the noise is virtually identical to my description. Lastly, I think I could feel the vibration in the floor board rather than in the steering wheel. My noise was only noticable when slowing down. Around 35 MPH the noise would occur for less than 1 second. I also never heard anything when the outdoor temperature was above 40 F.

Good Luck!!
 
Rumble strip sound is indicative of a dry spindle brass bushing. Do a search on spindle bushing and you'll see lots of pics and discussion. If you think you have the original brass bushings, then pick up a new set for both sides and grease them. Otherwise, simply take them out and grease them up on the inside where the axle shaft goes through.

Good luck.

edit: found a thread where I posted pics: https://forum.ih8mud.com/80-series-tech/74563-spindle-bushing-question.html
 
Back
Top Bottom