Installed PFran Interior LEDs

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 14, 2008
Threads
52
Messages
1,275
Location
Wenatchee, Wa
My PFran LEDs showed up today and I got around to installing them. Pictures do not do this mod justice, they are effin bright! Somehow when installing the festune in my erg80 rear hatch I somehow shorted out my dome fuse. Scared me to death, thinking I may have just made a very expensive mistake, buying pulled another 10a fuse from the dash and tested everything out. So now I need a new fuse. Also got the 5w reverse lights for the LC and for the tundra. Looking forward to getting these done and movin onto the instrument panel
image-3953071099.webp
image-1594856026.webp
image-1985619575.webp
 
damn... those are bright, hurts my eyes looking at the pics. Nice mod!
 
x2 cause I'm keen
 
Thanks for posting the link LivinOffroad, I could not get back on here. I am waiting for it to get dark before I install the reverse lights. I am very excited to get these in. I actually kind of wish the map light was a red LED instead of the same bright white as if I really need to use it when it is dark, it is going to blind me and everyone who passes by! I am very pleased with how the transaction with Paul went (PFran), and he is a Mud Vendor/Sponsor.

Follow the directions on the website and all will be fine, I would get some rubber/nitryl gloves though as I think this might be part of the reason I shorted the system causing the fuse to blow. I can not believe just how bright the door courtesy lights are. Even with the dome light off they light up quite a bit. I am sold on LEDs, they are worth it and will be talking to paul about putting together a kit for my 08 tundra.
 
It finally got dark enough to install the 5w Cree reverse lights and like the interior shots I got, these silly iPhone pics do not do them justice. Pre and post shots.
image-3064671896.webp
image-324866691.webp
image-1411805100.webp
image-1839034067.webp
 
I literally had my reverse lights on and the camera just did not pick it up. But it picked up the light output from the LED reverse lights.
 
I ordered the 80 series kit #3, and looked on the website and nobinfo I can find. So there are 4 doors, and 5 bulbs in the kit? Along with three large panels and one smaller. So I put four bulbs in the doors (one extra?) And three in the ceiling, 2 dome and one map, so I have one extra panel, along with a socket adapter, and a bullet adapter. I'm thinking my rear hatch has been replaced because I see a light in the posted pics on this thread, but I have no light in my rear hatch... Ideas on where the 5th bulb goes? I looked, no ashtray bulb either. This is what I have "extra"
IMG_20150605_164049624_HDR.webp
IMG_20150605_164049624_HDR.webp
IMG_20150605_164049624_HDR.webp
 
One is a spare. Which reminds me that I need to replace my dome light as it's been flickering like an epileptic on a bad acid trip at a disco convention for some time now.

But even with only something like 3 or 4 of the bulbs? in the panel still working, still gives off immensely more light than the OEM one.
 
It's a spare. I had to use it right out of the box. I think I have my front still working. The other dome lights have crapped out already.
 
They sell the same LEDs in packs of 10 on Amazon for basically nothing. All the ones I buy in variety of sizes already have a few duds but they are so cheap I can't complain.
 
Coming from the camera electronics and control world the quality of all these Chinese made LEDs have left me angered at best. Nothing against PFRAN at all. He tried to make me a happy as a customer and even changed out some of the wiring because it was better but now it's just a "me" issue. I need to get over the fact that there is a cheap Chinese alternative and I just need to accept it and move on because it seems a lot of folks here want the cheap alternatives and find that throwing away and trying again is merely a strategy. It's just not one I follow.
 
Coming from the camera electronics and control world the quality of all these Chinese made LEDs have left me angered at best. Nothing against PFRAN at all. He tried to make me a happy as a customer and even changed out some of the wiring because it was better but now it's just a "me" issue. I need to get over the fact that there is a cheap Chinese alternative and I just need to accept it and move on because it seems a lot of folks here want the cheap alternatives and find that throwing away and trying again is merely a strategy. It's just not one I follow.
Well said I can't even figure out what is good quality when ordering LEDs anymore.
 
I really recommend the ones from supercarrera. Based on George's I believe.

I'm still trying to find a quality LED backup bulb replacement.
 
Back
Top Bottom