Hiccup when Secondary Opens

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
284
Messages
8,118
Location
Kansastitty
I run a '77 2F with a Big Cap and a ported vacuum '74 F carb. Everything about it runs great except when I mash the throttle and the secondary opens. There is a pause/hesitation/hiccup then is runs great. If you floor it from a slower speed it transitions smoothly. At first I thought the little flapper valve with the weight on it (below the secondary throttle plate) might be too light, so I added about 1/4oz of lead stick-on wheel weight...no difference.
Everything is either new or rebuilt. Jim C curved my distributor, timing is at 7*BTDC.
Whaddya think?

BTW this did the same thing with two different carbs. One ran fine on my old '74F.

Ed
 
Strum,
No vacuum secondary. Manual progressive, but it does have the flapper beneath the secondary that does not open until the engine is sucking enough.
That is why I suspected that the larger displacement 2F was sucking enough more than the F that it was opening too soon, hence the weight.

Yes, I wish JimC or Marks W or A would chime in. A Poser comment would be welcome, but he runs a Weber 38/38.


ED
 
The other carb was identical except for the ported vacuum. I think that weighted throttle deal is the cause.

Ed
 
Ed,
It is endemic to the extremely crude mechanical (not manual) secondary design. When the pedal is tromped fast, the secondary flies open, but there is not enough air velocity initially to pull fuel from the booster.

Two possible engineering fixes:
1. a double pumper design, like a Holley mechanical secondary carb.
2. a vacuum (load sensitive) secondary that opens as engine demand requires, like an Aisan 38/40 or a Holley vac seconday carb.
 
Strange to see the word "endemic" used in reference with a carb, but I guess the carb does have a medical type problem tho.
 
Ed,
It is endemic to the extremely crude mechanical (not manual) secondary design. When the pedal is tromped fast, the secondary flies open, but there is not enough air velocity initially to pull fuel from the booster.

Two possible engineering fixes:
1. a double pumper design, like a Holley mechanical secondary carb.
2. a vacuum (load sensitive) secondary that opens as engine demand requires, like an Aisan 38/40 or a Holley vac seconday carb.


Is this due to the volumetric difference between the F and 2F? Because I never had this problem on the F.
So you are saying to live with it or considering changing carbs? I thought by adding some weight to the "flapper" plate that I might smooth the transition?

Thanks for the input, always appreciated!:)

Ed
 
I take it there is no accel. pump on this carb ?



Yes, but only on the primary side.....I think. That's why Jim suggested a double pumper Holley.


Ed
 
Ed,

I ran a few different early 70's Aisin NON USA carbs for a F motor on a few different 2F's over the years. One of them had an RV cam in it, all were in tip top shape with good compression and vacuum. I never had a flat spot, all ran great.

I never rebuilt the carbs because I bought 4 or 5 of them brand new from Spector for variouse different trucks.

I don't think the carb size/format/etc is your problem. Maybe the Non Usa version and the ported vacuum is the reason that I had no issues?

Not enough of an expert to say one way or another but it did work for me.

-Stumbaugh
 
I know I keep harping on this weighted flap, but as I posted, when I put it under full throttle at a lower speed, the transition from 1 to 2 barrels is very smooth. That flap thing should open more slowly........i think:)

Jon, I do have the ported vacuum on this carb. What other features does the non-USA carb have/not have? I kinda frankencarbed this. The base is from a Cali-spec '74 carb that had the EGR plate in it. So basically I just used the cast iron throttle body on an otherwise reg'lar ol' '74 carb. My mods should not have caused any problem because it ran exactly the same with my old '74 carb.
Initiually I thought it was because I was running a vacuum advance distributor w/o the vacuum hooked up. But that was not the case, evidently.

Thanks for all the help!

Ed


BTW, I only pull about 16in of vacuum on a motor with less than 1K on it. Been that way since assembly.??????
 
Last edited:
Have you tried advancing the spark a little, Ed? Or set the timing for highest steady vacuum at idle?
 
Have you tried advancing the spark a little, Ed? Or set the timing for highest steady vacuum at idle?

I've got an in-cab gauge, but I also have one to use under the hood. I'll try that. So far, I just used the BB and a timing light. If I time it according to vacuum, do I still disconnect the vacuum advance?
THX,
Ed
 
If you are timing it at idle according to vaccum, there should be no vacuum to advance the dizzy, unless something is whacko. So you could plug or not, but shouldn't need to.

I think most folks find 10-12 BTDC a nice place to be....
 
If you are timing it at idle according to vaccum, there should be no vacuum to advance the dizzy, unless something is whacko. So you could plug or not, but shouldn't need to.

I think most folks find 10-12 BTDC a nice place to be....

OK, its just that every time I have used a light, I thought you were supposed to disconnect the vacuum advance.
Wonder why it likes 3-5* more than the FSM says? Could it be in your case, the altitude?

Thanks,

Ed:)
 
You are supposed to disconnect (and plug) as a failsafe, but if it makes a difference at idle on a F carb, you should find out why! Some carbs (like in my 84 pickup) have one of the ports open to vacuum at idle.

I found the 5 degree beyond factory using the max vacuum then dropping a degree or two to avoid idle miss. Others have reported the same findings. Maybe it is an elevation thing, but I'm not certain. I know that there are also leaner jets for elevation, at least in the simpler carbs.
 
I have had a similar problem. I replaced may carb because it would start with a primer of gas directly in to the carb and then it would die. I had no idea what to do so I got another one. I installed a Weber 38mm and left Georgia for Alaska. Part way in to the trip the 40 began sputtering out around 40 mile per hour. It was fine up until 40 mph then it basically stalled or just sputtered. I could drive all day below 40 mph but it stalled above that. It went on like this for several days but eventually corrected itself and worked fine.

My point behind all this is that it my be something other than the carb. It appears my problem was, but I have no idea what.

Any ideas?? I have the same carb today (10 years later) and have no problems.
 
Ed, that throttle body may be the source of your problem. The vacuum porting of a '74, particularly a CA. '74, might not be the same as the so-called non-US, or pre 1970 carb. Maybe a call to one or the other carb guys could nail that down for you.
Wasn't '74 one of the years that used both vacuum advance and vacuum retard?
 
Honk, it did the same thing with the old carb so I doubt the throttle base is to blame when. If anything it is a carb/engine compatibility problem. The carb has two vacuum ports on it, the full manifold vacuum for the choke breaker and the ported vacuum on the passenger side of the carb. I only use the ported vacuum for the FJ60 distributor.
I think that flapper on the secondary is opening too soon or too fast. It is really more of an annoyance than a problem.

Thanks,
Ed
 
Back
Top Bottom