Help with my A/C

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 6, 2008
Threads
144
Messages
650
Location
Calgary, Alberta - Canada
I posted this one on the Diesel forum but later relaized the same system is common with the gasoline 80's so I thought I may get more advices here.
I brief, here's my conclusions:

"It seems from my visual diagnostics and the recommendations of other forum members that the Thermal Expansion Valve (aka TXV) is the culprit and is a common failure item in the 80's.
I was wondering if anyone changed theirs or had it changed somewhere? What it takes to have it replaced as far as shop time and is it easily accessible.."
If there is any picture anywhere to show its relative location that'd be great..

Cheers

Original Thread here:
https://forum.ih8mud.com/diesel-tec...-diagnoising-my-air-conditioning-problem.html
 
I would strat with High and low pressure check first. Depending on the high and low comparison it could be the expansion valve in the evaporator behind the glove box. There is a full write up with pictues that is very helpful. Heater switch could not be adjusted correctly either. On gas engines there is a thermal cut off switch that cuts the AC when the coolant temp hits 225 I beleive as a safety mech. So could be a engine temp issue. Also check the condensor, a good cleaning could help with simple green and a garden hose.
 
I did mine without any fsm or manuals when i replaced my evap core. You can get it out and replaced in 2 hours if you are a do it yourself type of person. I would recomend a fsm for the job because it will save you some time on disassembly. I also replaced my dryer at the same time cause the evap, expansion valve and dryer cost me just over $100 bucks shipped. My air is cold as ice now. Good luck if you need the parts you can find them here www.techchoiceparts.com i am not afiliated with them.
 
Thanks "mkguyvr"
If it took McGyver 2 hours, it'll probably take me a day :D
Did your truck had the same symptoms as mine? The pipes are frosty in the engine bay but yet the AC is blowing warm air inside!!

Could you please give me a bit more details on what this job entails? Per the FSM, the evaporator can be accessed without taking the whole dashboard out, just the glove compartment, is that right? (I hope the same applied to my vehicle, it is RHD!)

So, as I see it, and please correct me if mistaken:
- Drain the AC system of refrigerant (probably have to take it to an AC specialist for this)
- Take the evaporator assy out with the aid of the FSM
- Replace the TX valve with its O-ring(s)
- Put everything back again under the dash
- Replace the dryer (might as well)
- Have the AC shop charge the system again..

Does this sound logical?
Cheers..
 
No mine had the dreaded dead dog smell, could search that, it was blowing cold death smell and ended up being a hole in the evaporator that created the perfect place for a pungent bacteria to grow along with dog hair and leaves (nasty) Anyway i replaced all of the above mentioned parts and did some lysol treatment and its as good as new. It does sound like your exspansion valve is not opening causing the backup in the system.
 
mcguyvr: how was the quality of the parts you bought from techchoice parts, same as OEM, and where were they made? The price is almost 1/3 of OEM, even with a discount.
 
mcguyvr: how was the quality of the parts you bought from techchoice parts, same as OEM, and where were they made? The price is almost 1/3 of OEM, even with a discount.
The evap had China stamped on it but was identical to the one that came stock. All of the parts worl great and are identical. I would not hesitate to buy from this company again, had parts in two days. AT least it didnt have Mexico stamped on it, I have had some horror stories about parts from there.
 
Back
Top Bottom