help with clutch problems

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 10, 2006
Threads
175
Messages
1,382
Location
Grass Valley, CA
I just put a 350 in my cruiser and I am having a hell of a time with the clutch. I have a SM 420 and a three speed case, I used the stock slave cylinder which seems to be what most people do...however, I can't get the clutch to disengauge. The slave just isn't pushing it far enough. I rebuilt both the master and the slave and no change. If anyone has any ideas it would be great. thanks.
 
You can either get a low profile 11 inch clutch, or a longer throw hydraulic system. There is a thread on this topic on pirate4x4.com, where all your local buddies hang out.

Not that we are trying to get rid of you.

Welcome :beer: :flipoff2:
 
yeah, the pirate 4x4 thread is me too. I was just asking here too becuase I thought maybe someone would have an idea to avoid ripping out the tranny yet again...however, it looks like my problem is that I used the 12" clutch. I researched just about everything before I started this project....but not the clutch, I figured that was pretty straightforward....next time I'll know better. thanks
 
You need the low profile pressure plate, I had the exact same problem.

Check here <https://forum.ih8mud.com/showthread.php?t=81882&highlight=low+profile+pressure+plate>

First post after search.

Wish I could tell you how to fix it without dropping the tranny, but that is how it goes.
 
Yeah, I have sorta conceded that I am going to have to drop the tranny again....however, am I going to need to change the flywheel too? Do they make a 12" low profile?
 
OK...so I put in the right clutch, I used the cast fork and it's still not working. Does anyone have any other ideas...I'm really getting tired of taking the transmission out now.
 
OK..here is what I've got going on now. I put the 11" clutch in. I used the long T/O barring. I used the flat cast fork. I have a 350/sm420 and I have the Advanced adapters braket for the LC slave. I rebuilt the slave and master. They work fine. I put it all back together and it's actully worse now then it was with the 12". I can't even get it to release a little bit. What is going on???? I put the truck in gear and put a rachet strap on the rear axle and hooked it to the fork. I took the rod out of the fork and let it be totally free. Then I just started ratcheting away and rocking the truck trying find a spot where it might release...it never did. I went untill the fork was against the bellhousing and it never released. someone give some some idea what the hell is going on. I'm about to do something I swore I would never do and take it to a shop...yikes...anyone have any ideas? Anything at all?
 
chevy trucks use hydraulic clutches now and the throw is short is your pivot ball screwed in all the way and is the to bearing for a diafram type clutch the 3 finger one is not the same its tapered different also the slave needs to be as close to the bell houing as possible for the short throw ive never had this problem since i center the toyota clutch on the chevy fly wheel drill and tap it and just use toyota parts whent through this years ago now 27 swaps later still no problems someone should make a flywheel for this doubt this will help but maybe somthing here you can use good luck
 
i didnt read right since you have a chevy tranny you need a chevy clutch 85 chevy trucks have a hydraulic clutch and the throw is short using one now in a v8 toy and it works well also used bellhousing and fork from same truck and no problems we had these problem years ago when we mixed parts sorry for earlier info also one time i didnt tighten bolts down slow and even and clutch didnt work redid bolts and it worked fine hope you get it solved
 
Back
Top Bottom