Help Needed with Pulling 3FE AFM

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 11, 2012
Threads
20
Messages
83
After test driving my FJ80 after a heck of a lot of work (no one died, yay!), I noticed something after the drive and pulling back into my driveway. Despite my tune up (new plugs, wires, cap, rotor, air filter, PCV, etc), I would occasionally get an idle that would dip below the 600-650RPM area and it would get a little rough, hanging around about 450-500RPM. I'm working on a laundry list of things to check and one of them is the cleanliness of the AFM. I did some searching last night, but didn't find any specific directions on how to remove the AFM for cleaning or where specifically to clean it. I've pulled MAFs and cleaned them before, but this is obviously a little different. I am aware of the two screws of death (don't remove the socket), but that's about it. Any help you can provide me on cleaning this delicate, precision part would be greatly appreciated. Thanks!
 
I removed mine by unplugging the wiring harness (and don't loose the little wire retaining clip). taking off the hose clamps on the tube side and the the 4 screws that attach it to the air cleaner lid. There may be another mounting bot too, but I can't remember.

Should lift off after that. There's not a lot to clean other than the air vane that is inside and the housing itself. I used carb cleaner and it's been fine ever since.

Since the electronics are in a sealed portion of the unit, there is no real reason that you would need to clean them.

Good luck
 
Low idle is almost always related to a vacuum leak of some sort. While it is related to the AFM, it is usually not caused by the AFM but rather a cracked intake tube, bad gaskets, anything that will allow unmetered air into the system.
 
Low idle is almost always related to a vacuum leak of some sort. While it is related to the AFM, it is usually not caused by the AFM but rather a cracked intake tube, bad gaskets, anything that will allow unmetered air into the system.
I think you're right. I had removed the intake hose to change the air filter and clean the throttle body. Not sure if I'm the only one, but it was a beast to put back together. Are there any good pictures or diagrams that show how that intake hose should look stock?
 
There's only 1 way it goes back together. The accordion section is closest to the throttle body.
Intake.webp
 
Thank you, jon. I may have found my vacuum leak. It looks like the rubber tee coming off of one of the primary rubber elbows had gotten dry and cracked, allowing air to get in. I'm working on a home bodge on it until I can source a replacement - I will probably replace both sections just to be safe.
 
So I need to ask...what are the two screws of death...are you referring to the plugs on either side of the plug for the AFM?

....I may have removed them at one point and I have been having issues with it ever since (won't start unless AFM is unplugged and will die as soon as I hit the pedal).

What have I done to my poor LC?
 
So I need to ask...what are the two screws of death...are you referring to the plugs on either side of the plug for the AFM?

They're right on the plug/connector for the AFM itself.

The correct way to disconnect the AFM is to move the little wire clip on the connector and then just pull the plug. The wrong way is to try to unscrew the the AFM side of the connector.
 
What have I done to my poor LC?
You busted your AFM by removing the 2 screws and pulling out the guts. It might be able to be repaired if you're good with a soldering iron. Source a used one from Cruiseryard.com or anyone who's parting out any LC with a 3FE motor (1988-1992).
 
@mphil
Thank you, jon. I may have found my vacuum leak. It looks like the rubber tee coming off of one of the primary rubber elbows had gotten dry and cracked, allowing air to get in. I'm working on a home bodge on it until I can source a replacement - I will probably replace both sections just to be safe.
I'm curious if you ever bothered to clean the inside of the AFM and if it had any effect?
 
Back
Top Bottom