Help-Headlight wiring/conversion

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 5, 2014
Threads
3
Messages
163
I am in the middle of grafting a 2005 Tacoma grill and headlights onto my 94 LC. My problem is getting the 4 headlights (2 bulbs/4 wires each side) wired into the Tacoma single lamp 3 wire headlight. I have identified what is high and low beam on the Tacoma light but I can't get it to function with the high of the LC. I'm confused, I never thought this would be the hard part of the conversion! Can somebody do a dumb down drawing of what I need to do to get it to function as it should?

20170123_193059.webp
 
The bulbs with high and low in the same bulb usually share a ground. In that case you'll need to tie together the two grounds from the LC connectors (or supply an adequate one) and connect each 12V line to the respective H and L filaments on the Tacoma bulb. Some vehicles might switch the ground instead of the +12v so be careful. I have never worked on this in my LC.


Badass conversion by the way.
 
Ok, I'm confusing myself each time I write this. So here it goes. Your driver side uses a pair of common wires colored red with a blue tracer. That should be the common for the headlight the high Beam on the driver side uses a red with yellow tracer, that should be the signal wire for high, the signal for low should be from a thin yellow with a red tracer. The other side is set up similarly but using different color wires. Just find the wire color that is common to both bulbs and that's the common and then the other two wires are the switched ones. More info on the conversion, I like it!

IMG_4568.webp
 
Last edited:
I believe that land cruisers and most vehicles have switched ground headlights. Meaning you should have a 12v+ to both headlights in your original harness. The lights come on when a ground is applied. So you only need to combine the 2 positive wires down into one and use the ground signal from each of your original lights.
Unfortunately it doesn't work that way.

+12V is supplied to both HI & LO beams from the headlight relay (which comes on with the LO beams).
The ground is then switched for the HI beams by the dimmer control switch.
 

Attachments

Last edited:
Unfortunately it doesn't work that way.

+12V is supplied to both HI & LO beams from the headlight relay (which comes on with the LO beams).
The ground is then switched for the HI beams by the dimmer control switch.

A relay could be used to make the conversion to positive switching for the HI beam.
dang it you caught me before I changed it lol and I changed it again and it isn't still incorrect. I didn't have the wiring diagram and forgot about the autolight feature which changes things.
 
dang it you caught me before I changed it lol and I changed it again and it isn't still incorrect. I didn't have the wiring diagram and forgot about the autolight feature which changes things.
After re-thinking this, I think it will still be OK to wire it as you mentioned. Sure, the LO beam has a fixed ground, but the function shouldn't change.
 
The bulbs with high and low in the same bulb usually share a ground. In that case you'll need to tie together the two grounds from the LC connectors (or supply an adequate one) and connect each 12V line to the respective H and L filaments on the Tacoma bulb. Some vehicles might switch the ground instead of the +12v so be careful. I have never worked on this in my LC.


Badass conversion by the way.

It is bad ass. Not sure if you know that the grounds on the headlights on the 80's are postive
 
OK, with lights on low I get 12v between the 2 wires on the low plug and have what looks to be 12v to grnd on both wires on the high socket. When the high beam switched on I still have 12v to grnd on one wire and the other drops to 3v to grnd. If I terminate the 12v wire from high socket to high beam lead it does not light the high beam element. I hope this makes sense to someone because it doesn't to me.
 
I think your going to have to add a relay triggered by the high beam ground signal. This will turn on the high beams. You could then pull the 12v for the high beams from either the dedicated circuit, or straight from the battery (with a fuse)
 
I think your going to have to add a relay triggered by the high beam ground signal. This will turn on the high beams. You could then pull the 12v for the high beams from either the dedicated circuit, or straight from the battery (with a fuse)

I'm not understanding why there is 12v to grnd on both leads at the high beam socket when I'm switched low and I keep 12v to grnd on one of the leads but drop to 3v on the other when I switch on high.
 
what the high beam switch is doing is turning "ON" the ground. I'm not sure what the purpose of the ground leg having voltage is. You can see on the switch where the 12v+ comes in to the "Flash" circuit.
 
Make it simple.... use a hid hi/lo wiring harness and some hids just for fun. 3 wires to splice in..... low beam power, high beam power and ground to the harness. Harness will take care of the rest and plug right into some h4 hids.
 
I'm not understanding why there is 12v to grnd on both leads at the high beam socket when I'm switched low and I keep 12v to grnd on one of the leads but drop to 3v on the other when I switch on high.

My high beams do not come on, and I measured this same thing today. Like you, this makes no sense to me, so if anyone has an explanation I'd love to hear it.
 
My high beams do not come on, and I measured this same thing today. Like you, this makes no sense to me, so if anyone has an explanation I'd love to hear it.
Sounds like a bad high-beam switch.

Do the high beams come on when you pull the stalk towards you? ("flash" mode)
 
Reviving the thread. Would like an update and some pictures and info @Lcshack
 
Reviving the thread. Would like an update and some pictures and info @Lcshack

Hey 93
I have everything mounted with low beams and turn signals working. I've started getting the hood to match up to the profile of the grill. I still have some inner structure to add and figure out the high beams still, haven't messed with it in a while. Just too busy lately!

20170128_160812.webp


20170131_153936.webp


20170201_181828.webp
 
Back
Top Bottom