Head Gasket Replacement

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 8, 2015
Threads
10
Messages
62
Location
Alabama
While I am waiting for my plug wires to come in tomorrow, I figured I would show some of the pictures from the tear down and rebuild. It is a 97 with 268k miles. Has been neglected for quite some time.
I honestly do not know how the vehicle got me home after purchase and putting 1000 miles on it.
ImageUploadedByTapatalk1450237449.057033.webp


Exhaust Removed from head
ImageUploadedByTapatalk1450237515.096792.webp


Buildup from oil leak
ImageUploadedByTapatalk1450237642.447026.webp


Head about to be removed
ImageUploadedByTapatalk1450237790.884257.webp


Head removed with gasket still on block
ImageUploadedByTapatalk1450237982.411067.webp




Sent from my iPhone
 
Cylinder 1
ImageUploadedByTapatalk1450238115.260693.webp


Cylinder 1 of head gasket from block side
ImageUploadedByTapatalk1450238215.959717.webp


Cylinder 6 of head gasket from block side
ImageUploadedByTapatalk1450238275.584537.webp


Cylinder 1 of head.
ImageUploadedByTapatalk1450238337.060078.webp


Notice pitting/erosion? Head shop took .018" off to remove this imperfection.
ImageUploadedByTapatalk1450238460.509930.webp



Sent from my iPhone
 
Front main seal
ImageUploadedByTapatalk1450238564.390722.webp


In the process of cleaning
ImageUploadedByTapatalk1450238621.433667.webp


Picked the head up. All nice and clean
ImageUploadedByTapatalk1450238670.322006.webp


Alternator Brushes
ImageUploadedByTapatalk1450238766.068534.webp


Old plugs vs new
ImageUploadedByTapatalk1450238832.744536.webp



Sent from my iPhone
 
Head shop machined off .018, I seem to remember something in the FSM about not being able to machine off that much stock, maybe I read the manual wrong?? Perhaps Cruise Dan, or Beno can answer that question.
 
They mention a max warpage. I didn't instruct the machine shop to only remove up to a max amount. (That was my fault) So when I picked it up they told me what they removed. At this point, if there is a problem, I will drop a different engine in it or find another head.


Sent from my iPhone
 
Since this is an overhead cam engine, when removing that much stock, how are you going to deal with the extra slack now in the cam chain? Are you going to run a shorter chain or go with a thicker head gasket?
 
I will run it as is for now. If all is well after a few 1000 miles, I will replace the chain along with a few other items I didn't replace with the head job. The current chain is probably the original and has stretched over time? I am now adding to its existing slack with the head. Maybe a new chain will put it where it should be.
 
Just as an FYI, This motor has a neat little built in Hyd. cam chain tensioner, that will take up a certain amount of chain slack, but it has it's limits. I read in another one of your post that you now have this motor back together and it won't start. I'll be the first to admit I'm no expert on this motor, but since the shop did mill that head a lot, did you happen to check your valve to piston clearance. I hope you didn't have contact between the valves and pistons, and now have some bent valves, that could be why it won't start.
 
All that I have done to check if there is interference is rolling the engine over with the crank bolt. If there is a problem, it has already occurred. I do have compression which is a good sign of no air leaking by the valve.
 
Since You say you have compression I'm sure your valves are fine then. One thing I would do since you said it won't start, would be to go over your cam timing marks again.
 
Back
Top Bottom