hdj81 exhaust

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 21, 2005
Threads
963
Messages
9,414
Location
Powell River, BC
Well it would seem I'm going to need a new exhaust in the near future. There are a few options out there for premade 3" stuff from a few sources, but they are all $1,000 and up, but I'm cheap and still need to do my BeB and other things.
On my way home yesterday I stopped at a local muffler shop and got an estimate for a 3" shorty type exhaust. The idea is to start from the existing exhaust manifol flange, down to a new flex connection, then a long(ish) glasspack alongside the frame underneath the drivers side (RHD) and a 90 out just before the rear wheels. Keeping everything tucked up as high as possible, which is a little tricky with the 3" pipe.
Quote was for $500, seemed reasonable to me. Anyone running a similar setup?
The only downside is going to be mounting sliders. One of my club members has done something along these lines already, using 2-1/2" pipe from the stock resonator back. He has an idea for sliders for his that I just mind end up plagerizing :)
IH8MUD™ Forums - View Single Post - HDJ81 exhaust 3"

And why does the stock exhaust have 3 mufflers?
 
I paid $400 at local shop to have dual 2.5 run to just befor the back tires on my 89 s-15. It had Lt1 and 4wd. So it was tight to run. Just had to make some heat shields to keep from vaporlocking the fuel lines. This was at the best of the two local shops.
 
Jeff, I called a place I found advertising in the Buy and Sell for performance exhaust and they quoted me approx $600 for a straight through 3" from front to rear- that's sans muffler. I can't remember the name of the place right now...

Might be worth doing a run across the border as well- take the better half shopping in Bellingham for an afternoon.
 
ever since i saw that thread i kept thinking back to this LC's 3" exhaust from outback...just as an idea...
i'm no expert but i hear each 90degree turn costs you some HP, significantly?? so the bend on this one i thought would be more efficient? check out the japanese welds! like a motorcycle exhaust. (last pic on the bottom, not much for ground clearance tho...

Outback Imports - Pictures of Toyota LandCruiser HDJ81 LTD VX 4x4 Diesel

just wondering, what if you tucked the pipe as high up and just angled it down towards the ground and just avoided the side outlet all together...or taking it all the way to the back end . . . ?

ahh, one more on my to do list...my "want" list...
 
That looks like a huge target back there, hence the reason I wanted to exit mine similar to the picture I attached. Currently mine runs fell length, exits out the back, with some big shiny rice-burner type bling bling mondo huge exhaust tip, that I of course smacked on my 1st wheeling trip and busted the mount off.
That and my flex connection leaks, and another leak where it exits the 1st muffler/resonator.

But why do these things (mine anyways?) have 3 "mufflers" ?

I'm thinking of just leaving mine at the 2 1/2" (stock) diameter. The change to 3" is freaking huge, and if I go to such a significantly shorter pipe with less restriction, it should be almost as good..yes?
 
something to do with lowering EGT's and putting less strain on the turbo i hear, easier "exhalation" for the engine kinda thing....i've read it is usually accompanied by uppin the boost to 14psi (i've heard 12psi too) but i can't find out why that's the magic number for a lot of turbos on diesel toyotas through searches....plus i'm no gearhead ...
 
Jeff, I've run nearly all my trucks with the exhaust dumping out the side in front of the rear wheels including my current one and I've hated it that way every time. The advantage is it is easy to do and easy to repair if you manage to destroy it on the trail. I always have one black back wheel and if it happens to be a steel wheel it quickly becomes a rusty black wheel. Diesel exhaust is more corrosive than you think. In my case I have a pto driven hydraulic pump above the rear axle as well as a hydraulic tank and associated plumbing. It makes it pretty hard to snake an exhaust through there too but when I swap my 3" turbo outlet onto my CT26 I'm going to try once again to get the exhaust behind the wheel where it belongs.

One of Steve's 3" kits showed up in Cowtown this week and I don't think you can do much better. It looks like an easy install.
 
3 inch exhaust is a tight fit over the 1st cross member, after the muffler and before the axle, even with a 1 in body lift.

The 3 in tube turns up after the muffler passes over the 1st cross member, over the axle and turn down after the axle before the 2nd cross member, stay up high and tight as possible in order to clear the axle at full up travel. (see 2nd picture)

3 in exhaust might be able to fit without a body lift, it will be tight and need header tape in the least.

There were 4 places the exhaust had to come apart in order to get back out and in for weld up and future removal.

I used madrel bends from this website Columbia River Mandrel Bending cheap cost great quality.

The exhaust is on a 94 FZJ80 with a 4BT Cummins and a 1 in body lift

kit used http://store.racing-solutions.org/3on4rasuexbu.html
exuast4BT80-1.webp
exuast4BT80-2.webp
exuast4BT80-3.webp
 
Last edited:
by the time I made a kit there will not be any diesel left at the pumps : )

with some "band" exhuast clamps (see the chrome things with bolts in before pics) you can twist, take in and out for fitting, trimming and welding...I love pre-made mandrel bends...
 
The 3" Steve is selling does look nice, I was trying to find a cheaper alternative really.
One potential huge flaw with the exhaust exiting in front of the rear wheels, I think it would fail a MOT inspection, as you are not allowed to have exhaust existing before/near a passenger area....I think.
Outback appears to sell the same exhaust for the same price, including installation. They also have another version for another $500, all shiny like.
 
I have heard that a common mod is to leave the middle muffle out, mine has the front muffler missing but its a bit louder that way from inside the cab
 
BC Inspection Manual:

'tail pipe termination' out of service criteria: "does not terminate within 50mm (2in) of outside perimeter of the passenger compartment expelling exhaust outwardly (includes trunk). FWIW
 
not exactly a similar setup, but i did run 3'' from the cat back. I opted to go over the frame for extra ground clearance (also the part that effectively created all the problems to begin w/) and all the way to the back. I think the price sounds right. I was under 500 for 3'' pipe front to back, 1 high flow cat, 1 muffler and all the labor. Keep an eye on LCDucatti's thread as well as it seemed to be turning up new options.

https://forum.ih8mud.com/80-series-tech/223533-new-3-cat-back-exhaust.html
 
Back
Top Bottom