Ground for replacement stereo

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 15, 2003
Threads
102
Messages
3,129
Location
Knoxville
I've replaced my factory stereo with a Sony CDX-GT810UW (nice upgrade to the factory stereo). I ran the ground wire for the new stereo to a bolt on the main metal bracket that holds the stereo, but got a fair amount of engine noise (interferance) coming through the stereo. So I extended the ground wire through the fire wall and tied it down with a bolt on the side of the engine compartment. Not as bad, but still getting a fair amount of interferance.

Any suggestions on a spot you all have used to tie the ground down would be appreciated?

Thanks,
Rookie
 
Straight to the battery always worked great for me to reduce noise. Use good quality finely stranded wire too. Make sure it is adequately sized too. Too small, and if will create noise.
 
I have a similar head unit with a harness adapter I got from Circuit City. No noise. IIRC the adapter was $15.
 
I have a similar head unit with a harness adapter I got from Circuit City. No noise. IIRC the adapter was $15.

The stereo (got from crutchfield) came with a harness that plugs directly to the factory harness. The only part that's not plug and chug is the ground wire. Did you not have to run a ground?
 
Straight to the battery always worked great for me to reduce noise. Use good quality finely stranded wire too. Make sure it is adequately sized too. Too small, and if will create noise.

The cable I used to extend the ground is pretty big (maybe 4/0 or 2/0). It's the same cable I used to wire power to an amp I added a couple of years ago.

When you say wire to the battery, you talking about running the ground to the battery negative post. That seems spooky.
 
Why would it be spooky? The chassis grounds to the battery. The body has a small grounding strap to the battery. The engine eventually grounds to the body. I also had good success with a 4 or 8 ga wire coming from the battery to a distribution block. I did the same thing with my power feed(properly fused of course). I never had any ground noise in my truck, even on the 0 bits IASCA software cd that was used for IASCA competition judging. That was back in 1991 or 92.

You could try a noise choke if that doesnt work.
 
Why would it be spooky? The chassis grounds to the battery. The body has a small grounding strap to the battery. The engine eventually grounds to the body. I also had good success with a 4 or 8 ga wire coming from the battery to a distribution block. I did the same thing with my power feed(properly fused of course). I never had any ground noise in my truck, even on the 0 bits IASCA software cd that was used for IASCA competition judging. That was back in 1991 or 92.

You could try a noise choke if that doesnt work.

I guess anytime I imagine hooking up to the battery, it's for power. I know the battery is grounded too, didn't know you could attach to the battery for ground.

Okay, so the power feed etc, comes through the wiring harness as I've currently got it, and the only thing I'm running to the battery, is a ground cable to the negative post?

Thanks,
Rookie2
 
yeah, that should work.

or you can tap into the ground wire on the factory harness. solder/heat shrink that connection, and youd be good to go. this might be the quicker/easier route for you right now.
 
yeah, that should work.

or you can tap into the ground wire on the factory harness. solder/heat shrink that connection, and youd be good to go. this might be the quicker/easier route for you right now.


That's what I was thinking about doing before... trying to get it back into the factory ground loop. Do you have a wiring diagram for the LX450. It shows two locations coming off the Radio harness labeled "GND". Wonder if it matters which one I tap into?

If you don't have the wiring diagram and want to see it, PM me your e-mail address and I'll shoot it to you.

Thanks again.
Rookie2
 
I think one is for the backlightiing circuit, and the other is for the radio. They would have to tie in together somewhere. I've got the wiring diagram on my other laptop (thanks to nate and his fsm download process).

Good Luck, and if you still have the noise, ask who makes a good noise gate or choke. Aftermarket head units seem to be more sensitive to ground noise.
 
The stereo (got from crutchfield) came with a harness that plugs directly to the factory harness. The only part that's not plug and chug is the ground wire. Did you not have to run a ground?

No, mine had everything in the harness.
 
Back
Top Bottom